56021A0WW General Electric Washer - Instructions

1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...

I placed both hands under the agitator 180 degrees apart, gave a quick jerk, and seperated the agitator from the coupling. With the agitator removed, use a socket and ratchet to remove the bolt holding the coupling to the spline. Remove the old coupling and slide the new one over the spline. Lightly tap on the coupling if necessary. Insert the bolt with the ratchet and slide the agitator back over the coupling and you are done.

I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008.

I also power washed the basket and tub before reassembly.

The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.

The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.

I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.

I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.

The entire job took 5 hours.

Removed the water level pressure switch and the water inlet valve to test parts for proper operation with an ohm meter. Electrically, the switches seemed to work fine so I thought it was probably a mechanical water valve problem. I ordered and replaced both parts anyway just to be sure and potentially save time.

Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received it two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.

I replaced both the tube and the pressure switch and still no luck. turns out that i didn't need either part. the little box that the tube hooks on to at the bottom left of the tub had a clog in it. we disconnected the tube from the switch and just blew through it. the clog broke loose and my washer works again!! decided that i was leaving the new parts on the machine. one less thing to worry about in the future.... ????

First raise the lid on the washer then remove the agitator by placing hands under the agitator 180 degrees apart and pulling up. Pulling up one side and then the other until the agiator lifts up and off. Mine was stuck tight so I had to really work it back and forth to get it loose. Be careful while lifting on the agitator because when it comes loose it could hit you in the face since you are over it while lifting. Once you get the agitator off use a 7/16 socket and 3/8 rachet and remove the coupling. Place the new coupling on the shaft, making sure to line up the splines on the shaft and the coupling and install the 7/16 bolt and thighten it. Place the agitator on the coupling by lining up the splines and pushing down on the agitator until it seats. Time to repair was 30 minutes.

First I removed the screws that held the hose drain hose clip in place. Removed the damaged hose. Placed the new drain hose clip at the end of the new drain hose. Re-inserted back in hole, pushed in hose to necessary depth then tighted screws, Very easy and painless.

Removed front cover, Control panel, top Cover, slasher unit, all very smiple stuff. the hub was broken and the spinner basket came right out. One half Hub attached to Spinner, Other half attached to Hub drive shaft. removing the Hub nut was the hard part. tried impack & socket, No luck. in removal. Had to usr Hammer & Chisel and bust Old Alum. Nut off. Clean up and replace parts. OK. Had to remove water pump and clear debree that went in pump when spinner Hub broke off . the spinner also bursted a crack in the outer poly tube when it cam apart.. Sanded the dmage area and Patched with a good coat of JB Weld. machine is working Like new. The parts all worked Great. the break down Chart was a great Help to get the right parts needed. Thanks

Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.

The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It required a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.

My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off and putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!

Had never repaired a washer before, but have several tools and enjoy working with my hands. Knew it would be cost prohibitive to call a repairman, and didn't have anything to lose. Quick delivery from partselect -- reasonable price, too. This was as easy as simply taking the whole washer apart (NOTE -- there are instructions behind the knobs inside the unit that are very helpful!) replacing the transmission and putting it all back together. Hardest part was getting the hub nut off of the transmission axle. To get it off (REVERSE THREADED, so 'tighten' to 'loosen') I used a 1 11/16 socket and impact wrench. Use the same tool to tighten (but go EASY...don't overtighten). This was not difficult, but just took some time. A couple of evenings later, we were washing again like NEW. Part cost around $160, labor was 'free' and much less than a new $500 top loader or $800 front loader. If you enjoy taking things apart and have some tools, then go for it!

I think finding the tools to do the repair took longer than the actual repair!

After unplugging the machine, turning off the water and disconnecting the hoses~ All I had to do was remove the top front panel~ I think that was 3 screws; remove the old part~ 2 screws, disconnecting a hose, and unplugging the 2 connections; put in the new part~ reconnecting the hose, 2 screws, plugging in the two connections; put the front panel back on~ 3 screws; reconnect the hoses, turn the water back on, plug the machine back in then tested it and it worked perfectly!

When the kids got home from school and I told them I fixed it they high fived me and said, "Way to go Mom!"

First I unplugged the washer from the wall and then I removed the front panel with a putty knife. I slid the putty knife in between the front panel and top of the washer to disengage the two clips (see parts diagram on Partselect.com). Then I removed the four nuts holding the motor. I then removed the motor and old belt. I installed the new motor and new belt and tightened the four nuts ensuring proper belt tension. The new motor included a new wiring harness and capacitor. The wiring harness installation instructions were easy to follow. Besure to read the all the instructions first before beginning to cut the old harness. Once the wiring harness was installed, the machined worked just like new. I did not need the Retaining Clip for Clutch since the new motor and clutch kit come as one assembly and there is no longer an actual clutch. The two-speed motor just has a pulley for the belt.