550WH Admiral Range - Instructions

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpf ... Read more ul ML

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not ... Read more a pretty picture, but that's how repair work is on old stuff.

I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove th ... Read more e screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that ... Read more matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

Simply unscrew the heating element attachment and remove, then replace with new one. My biggest problem was remembering how the oven door is removed to gain reasonable access to inside rear of oven. After exploring for a few minutes and pulling on oven door , it slide of it's hingrs - and then I remembered. Next problem was my wife making ... Read more me clean the oven when the old element and oven door was removed.

I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.

used drill to remove old screw

I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were ... Read more 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good dir ... Read more ections.

This worked out GREAT. We were about to purchase a new range when I found the needed parts were available. The stores we had contacted had told us our range was too old to have parts available. I had no problem with installing the receptacle at all. The pans went in easly as excepted. My wife is happy with her NEW arrangement. She d ... Read more oes not need to learn how to operate a new range. Thanks for your help. The instructions sent were clear and easy to follow.

Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if ... Read more I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).

I will begin by saying that not only will I continue to order my parts from PartsSelect, but I also highly recommend this business. If you call Whirlpool be careful that they forward your call for parts to some preferred vendor, which a customer might assume is Whirlpool but it is not. PartsSelect is the same type of business, but wit ... Read more h outstanding customer service. With regard to the drip pan, Whirlpool had not updated the part number for these as I found out when i called them. Whirlpool no longer uses the drip pans without the holes which is a serious problem since this could be hazardous to the owners of these ranges if you are forced to purchase the drip pans with the holes in them. That said, I ended up keeping my old drip pans, because if you spill grease under the new ones with the holes in them and since the range design with the fan built in on the top does not allow you to lift the top to clean under the pans, you could end up with a grease fire. This is not the fault of PartsSelect and they handled my order in a manner that I would give them a rating of exceptional for customer service.

new drip bowl fit perfectly and was a snap to install.