5321 - Parts

This is a genuine manufacturer-approved component which is designed for Dynabrade sanders and grinders. It is an identical replacement for a missing or a damaged pin that was installed on a new unit. This is one of the pins for the rear end plate. Refer to the owner's manual and the parts diagram for your model to ensure the correct repla...Read morecement procedure. Note, this high-quality pin is made of a durable metal and is sold as an individual item. A screwdriver and pliers will be needed to perform this repair.

This bearing is an OEM part direct from Dynabrade. The orbital sander bearing allows the shaft balancer to rotate freely. An allen wrench will be needed to remove the screw that is holding the bearing. This part is made of metal and is sold individually.

This replacement o-ring is an original Dynabrade part that is specially produced for use with sanders, drills and grinders. It is an authentic OEM item that has multiple uses depending on your equipment, please make sure to check appropriate diagrams for correct location and use of this o-ring. Note one durable rubber o-ring is included per order.

This is an authentic Dynabrade replacement part. The gear oil fitting is designed by the manufacturer for use in power tools such as sanders, grinders, and filers. This part is made of metal, and is placed in the gear housing to allow the injection of lubricant. You may require a screwdriver or Allen wrench when replacing this part. This item is sold individually.

This is an authentic OEM component from Dynabrade. The valve stem is constructed of durable metal, and is compatible with many sander and grinder power tools. This part assists with fastening the speed regulator into the throttle lever assembly. The valve stem is sold individually. A wrench set, screwdriver and pliers are often necessary ...Read morefor the proper replacement. Refer to the owner's manual for additional repair instructions.

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sol...Read mored individually. Replacing this item you would need a wrench to replace this item.

This an authentic Dynabrade replacement part used in buffers and sanders. The spring is used to absorb shock from the valve when tool is in use. It goes between the air control ring and the tip valve. A wrench may be needed to properly install this part. This item is available as an individual replacement part.

This is an authentic OEM component from Dynabrade. The speed regulator assembly is compatible with many grinders and sanders. This metal and plastic item secures the valve stem in the housing, managing the airflow in the device. A wrench is often helpful in making the replacement.

This is a genuine Dynabrade replacement part. The insert assembly is designed by the manufacturer for use in power tools such as sanders, grinders, and cut-off tools. This part is made of high-quality plastic, and is placed in collar of the motor housing. You may require a screwdriver or wrench when replacing this item. This part is sold individually.

This is a genuine original replacement part manufactured for use whit reciprocating saws. The metal gears fits into the gear case, and is driven by the pinion gear on the armature. The gear will come with the thrust ring, and needle bearing. The gear kit is sold individually.

This 3-speed wire harness is supplied by the original manufacturer for use in ceiling fans. It is an electrical component that connects the ceiling fan motor to the fan speed switch to allow the user to control the speed settings. Over time the wire harness may become faulty due to physical damage, loose connections, or electrical failure...Read mores. If it fails, you will likely be unable to adjust the speed settings, or the fan may not run at all. Before beginning this repair, turn off the power to the fan at the circuit breaker. Remove the fan blades and any other parts blocking access to the electrical components. Locate the wire harness which is connected to the fan motor and speed switch or control panel (depending on your model) and take a picture of how the wires are routed for the installation. Disconnect the wire connectors and remove the faulty harness. Position the new wire harness in the appliance and connect the wires to the appropriate terminals using the image you captured. Reassemble the fan parts. Turn on the power and test the fan speed settings to ensure that the new wire harness is functioning.