52434 Dynabrade Saw - Parts

This is a genuine manufacturer-approved component which is designed for Dynabrade sanders and grinders. It is an identical replacement for a missing or a damaged pin that was installed on a new unit. This is one of the pins for the rear end plate. Refer to the owner's manual and the parts diagram for your model to ensure the correct repla...Read morecement procedure. Note, this high-quality pin is made of a durable metal and is sold as an individual item. A screwdriver and pliers will be needed to perform this repair.

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check...Read more the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.

This is a genuine replacement part sourced directly from the manufacturer. The cylinder is commonly found in power tools from Dynabrade, such as die grinders, sanders, and drills. This part is made of metal, and is used to hold the rotor and rotor blade assembly. This item is sold as an individual replacement part.

This genuine Dynabrade part is OEM. It fits power tools including sanders, grinders, and various others. Bearings buffer moving parts by providing rotational support and securing position. These high wear components are replaced often for optimal performance. Sold individually.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Dynabrade tools. It is an identical replacement for a missing or damaged pin that was originally installed on a unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this ha...Read morerdware. Keep in mind this high-quality item is made of durable metal and is sold individually.

This replacement o-ring is an original Dynabrade part that is specially produced for use with sanders, drills and grinders. It is an authentic OEM item that has multiple uses depending on your equipment, please make sure to check appropriate diagrams for correct location and use of this o-ring. Note one durable rubber o-ring is included per order.

This is an authentic OEM sourced component which is specially made for use with Dynabrade power tools. It is an identical replacement for a missing or a damaged shim that was installed on a new unit. It provides a tight seal between connected components. Please make sure to refer to the appropriate diagrams of your model for the correct l...Read moreocation and application of this part. Keep in mind this high-quality shim is made of durable material and is sold in a pack of three.

This authentic manufacturer-sourced component is specially designed for use with Dynabrade power tools. It is an identical replacement for a missing or a faulty hardware that was installed on a new unit. Please make sure to check the owners manual and the appropriate diagrams of your model for the exact location and application of this pa...Read morert. Keep in mind this high-quality speed regulator assembly is made of durable material and is sold individually.

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sol...Read mored individually. Replacing this item you would need a wrench to replace this item.

This an authentic Dynabrade replacement part used in buffers and sanders. The spring is used to absorb shock from the valve when tool is in use. It goes between the air control ring and the tip valve. A wrench may be needed to properly install this part. This item is available as an individual replacement part.

This is a genuine OEM part. The Dynabrade tip valve is manufactured for use with orbital sanders, finishers and grinders. This metal and plastic valve often sits in the air inlet bushing, and is supported by a spring. The valve is sold individually, please see specific manual for additional repair information. A pair of pliers, wrench and a screwdriver may be necessary for installation.

It is a genuine OEM part that is designed for Dynabrade grinders and sanders. The valve stem is an important component that connects to the speed regulator assembly. It provides an identical replacement for a damaged or a missing part that was installed on a new unit. Check the owner's manual and the diagrams for your model to ensure the ...Read moreproper repair procedure. Keep in mind this high-quality valve stem is made of durable metal and is sold as an individual item. A screwdriver, a wrench set, and pliers might be needed to replace this part.