52221 Dynabrade Grinder - Parts

This part is an OEM from Dynabrade. Compatible with a variety of power tools, this item is sold individually. The rubber o-ring often provides protection from friction and leakage. Please refer to the specific manual for repair instructions.

This retaining ring is an original part from Dynabrade. Compatible with sanders, grinders and buffers, this item is sold individually. The metal ring is often used to help secure the valve stem in the housing. A pair of pliers are helpful with making the replacement.

This part is an OEM from Dynabrade. The metal pin is compatible with many grinder and sander devices. The pin helps to fasten the throttle lever assembly to the housing. This item is sold individually. A pair of needle nose pliers may be needed for the removal and replacement.

This is a genuine manufacturer-approved component which is designed for Dynabrade sanders and grinders. It is an identical replacement for a missing or a damaged pin that was installed on a new unit. This is one of the pins for the rear end plate. Refer to the owner's manual and the parts diagram for your model to ensure the correct repla...Read morecement procedure. Note, this high-quality pin is made of a durable metal and is sold as an individual item. A screwdriver and pliers will be needed to perform this repair.

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check...Read more the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.

This is a genuine replacement part sourced directly from the manufacturer. The cylinder is commonly found in power tools from Dynabrade, such as die grinders, sanders, and drills. This part is made of metal, and is used to hold the rotor and rotor blade assembly. This item is sold as an individual replacement part.

This genuine Dynabrade part is OEM. It fits power tools including sanders, grinders, and various others. Bearings buffer moving parts by providing rotational support and securing position. These high wear components are replaced often for optimal performance. Sold individually.

This replacement o-ring is an original Dynabrade part that is specially produced for use with sanders, drills and grinders. It is an authentic OEM item that has multiple uses depending on your equipment, please make sure to check appropriate diagrams for correct location and use of this o-ring. Note one durable rubber o-ring is included per order.

This is an authentic OEM sourced component which is specially made for use with Dynabrade power tools. It is an identical replacement for a missing or a damaged shim that was installed on a new unit. It provides a tight seal between connected components. Please make sure to refer to the appropriate diagrams of your model for the correct l...Read moreocation and application of this part. Keep in mind this high-quality shim is made of durable material and is sold in a pack of three.

This is an authentic OEM component from Dynabrade. The valve stem is constructed of durable metal, and is compatible with many sander and grinder power tools. This part assists with fastening the speed regulator into the throttle lever assembly. The valve stem is sold individually. A wrench set, screwdriver and pliers are often necessary ...Read morefor the proper replacement. Refer to the owner's manual for additional repair instructions.

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sol...Read mored individually. Replacing this item you would need a wrench to replace this item.