521E (1695702) Snapper Snow Blower - Parts

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

Snow blower discharge chute.

This hex locknut has a special locking feature to prevent it from loosening due to vibrations or movement. It has a 1/4 inch diameter and a 20 threads-per-inch pitch. You will find it securing various parts of your lawn equipment, such as blade assemblies, engine mounts, or handles. A broken locknut cannot fasten components together tight...Read morely. Replace any damaged locknuts to keep your machine securely assembled and functioning properly. Loosen a locknut from your machine by turning it with a wrench or a socket. This durable metal locknut is an OEM hardware. It is sold individually, so read your user manual to determine how many you will need. Consider getting extras if you are replacing one, as these locknuts tend to wear out together.

This is an OEM replacement part for Briggs and Stratton, Murray, Snapper, and Simplicity engines. When engaged the ignition key starts the lawn tractor. This part is made of metal and is sold in a set of two. There are no tools needs to use this part, as it comes pre-assembled and really to use.

This is a genuine manufacturer-approved item that is specially designed for Craftsman snowblowers. It is an identical replacement for a missing or damaged knob that was originally installed on a new unit. The purpose of this component is to provide a user with a comfortable grip to secure the adjusting chute. Please make sure to refer to ...Read morethe appropriate diagrams of your model for the exact location and the correct installation of this component. Keep in mind this durable plastic knob is sold individually.

This authentic replacement part is designed for use with Murray, Simplicity and Snapper snowblowers. Flange bearings are used to provide support for a shaft while reducing friction between rotating parts. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the roller reduces friction. Beari...Read morengs experience constant wear from pressure, heat, vibration, and friction. Because of this, many bearings need to be periodically replaced. Make sure to check the diagrams of your model for the exact location and the correct installation of this component. It is sold individually. You will need a screwdriver and a wrench set to take apart the housing in order to gain access to this flange bearing. Keep in mind the screws utilized to secure this component are sold separately.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

This handle is an original part from Craftsman for snow blowers. This part connects to the frame for steering and pushing the snow blower. You will need a wrench or an adjusting wing knob (part 1501260MA) to replace this handle. This part is made of metal and sold individually.

It is a genuine OEM sourced part that is specially produced for use with Murray and Snapper lawn and garden equipment. This is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. This high-quality carriage ...Read morebolt is made of durable metal and is sold individually, keep in mind the washer and other parts are all sold separately.

This is a Briggs & Stratton, Murray, Snapper, and Simplicity replacement part directly sourced from the manufacturer for use in engines and snowblowers. The choke shaft knob is made out of plastic. It might require a screwdriver and a socket set to replace this item. It will need to be replaced if it breaks. This part is sold individually.

This is a genuine OEM sourced part which is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It provides an identical replacement for a damaged or a missing component that was on a new unit. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the ca...Read morerburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. At some time the primer will lose its elasticity or crack and need to be replaced. It is made of high-quality rubber material and is sold individually. Keep in mind the #696824 Nut (Carburetor Primer) that helps to secure it is sold separately. Replacing the primer is a simple task, simply remove the old one and connect the new one to the hose.