51992 - Overview

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

Support a laundry appliance leg where it meets the top of a pedestal with this replacement leg guide. The guide fits into a top corner of the pedestal and helps hold the appliance foot in the correct position. Proper support keeps the washer or dryer seated securely on its raised base. Replacement may be needed if the original guide is cr...Read moreacked, bent, loose, or missing. Check the mounting shape and location against the equipment diagram before ordering. Installation may require lifting the appliance, so disconnect all power and water lines and have another person help move and support the unit safely.

The manufacturer-certified Fuel Tank Assembly is part of a kit including the fuel lines, fuel cap, and fuel filter. It will require a screw driver, and socket set, and is rated as "Easy" to install (Tip: drain fuel before starting repairs). This white plastic part attaches to the unit and holds the fuel and filter to prevent debris from g...Read moreoing to the carburetor. If broken or damaged from regular wear/fatigue, the part will leak fuel and must be replaced. Refer to your make, model and diagrams to ensure this is the correct part for you.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

This filter element is a genuine Toro replacement part that is sourced from original equipment manufacturer for use on handheld lawn and garden equipment. The purpose of this filter is to keep dust and other contaminates from going into the carburetor. Keep in mind, one high quality foam element is included per order.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

Genuine OEM replacement part, this part is sold individually. This part is where the stringhead assembly is mounted on the Trimmers shown below. It attaches to the spindle. The thread mount on the spindle is a left hand thread.

This spark plug is an authentic Craftsman replacement part, and is compatible with chainsaws. The spark plug produces a spark that ignites the fuel in the engine. A socket wrench will be needed to install or replace the spark plug. This part is made of ceramic with metal and is sold individually.

Genuine OEM replacement part designed for use with string trimmers. It is the part of the trimmer that contains the cutting line. It is made out of plastic and it is sold individually. Please note the spool housing and the cap are both sold separately. When replacing this item no tools are needed. • Install the string head assembly on...Read moreto the gear head shaft by turning counterclockwise • Tighten the string head assembly securely