5100 - Overview

This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.

This screw is sold individually.

This part is sold individually. This nut can be found in various appliances including a dishwasher, air conditioner, washer, dryer, range/cooktop, oven, freezer, range hood, and refrigerator. There is a serrated pattern along the edge of the nut, which helps to avoid loosening while the appliance is in motion. Nuts may corrode or rust ove...Read morer time and will need to be replaced. You will need a wrench to screw the nut into place. This genuine OEM part comes directly from the manufacturer.

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near the transmission or the wheels of your machine. If you notice that the machine takes longer to stop or that there is a loud scraping or grindi...Read moreng noise when you push down on the brake, your brake puck may have worn out. If it is not replaced, you risk losing braking power, which leads to equipment damage or accidents. Before any repairs, make sure that your machine is turned off and that the spark plug is disconnected. To dissemble the brake assembly and access the brake puck, use pliers or a wrench to remove any bolts or clips holding it in place. With a screwdriver, pry the brake puck out of your machine. Since this genuine OEM part is sold individually, determine the number of pucks your machine needs by consulting your user manual.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This OEM Extension Spring measures .62 x 6.12 inches. It is a silver, metal, individually sold, part. It can be installed with pliers and has been rated Easy to install by customers. (Note: Installation may require a lot of pull force to remove and reattach.) The spring attaches underneath the tractor on the drive belt idler pully, to t...Read morehe axle support bracket, and is used to apply tension on the drive belt idler pully. If broken or overly stretched, likely due to fatigue, you will lose your forward and reverse drive, as the belt will no longer be able to transmit power. If this happens, the part must be replaced. Refer to your owners manual and model number to ensure you are selecting the correct part.

This authentic OEM hi-pro key, also called a woodruff key or key stock, is a metal component found in your lawn equipment that connects rotating parts. It is 3/16 inch wide and 5/8 inch long. It fits into a specially-shaped slot on a shaft and prevents the parts from moving or slipping out of position while your machine is running. To fin...Read mored and replace a hi-pro key on your machine, check your user guide for instructions. When removing the hi-pro key, insert a flathead screwdriver or needle-nose pliers into its groove and pry it out of its slot. Please bear in mind that this hi-pro key is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. It is a standard hardware which may have multiple applications. This part provides an identical replacement for a damaged or a m...Read moreissing hardware that was installed on a new unit. Check the diagrams for your specific model for the exact location and the correct application of this flat washer. Note, it is made of durable metal and is sold individually.