Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4875 > Instructions

4875 Hoover Range - Instructions

All installation instructions for 4875 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4875
76-90 of 141
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bad switch

  • Customer: Merwyn from Kingsport, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
As stated on order.

Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.

  • Customer: Lenice from Stuart, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.

super old Jenn-Air range needed an element

  • Customer: Edgar from Montgomery, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Pulled out the old one-couldn't find it ANYWHERE that was a comparable match except for partselect. shut off breaker to oven-put in the new one-hard to reach in due to limited space and hard to see due to sticking your head in an oven.used a mirror/flashlight to see behind element to unscrew and screw it back in.Other than space restriction and light-pretty easy. Works great! Thanks for HAVING the part!! :)

Had to replace grease filter

  • Customer: Donald from Cottage Grove, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Nice filter. Exact fit. Had a little ring to use to pull out to clean. Shipment was packed well.

Filter Worn Out

  • Customer: Thomas from Berlin, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Remove cover and install

Oven element burned out

  • Customer: Eugene from Satellite Beach, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The only trouble I couldn't remove the screws that held the wires to the element, so I cut the wires as close to the end as possible and attached new hardware. After that was done it was simple to reinstall the new element. Turned the power back on. Turned the oven on and it worked like new.

bake element not heating up

  • Customer: john from chatham, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
removed element and tested wirh ohm meter. No reading telling it was bad. Tested voltage from supply wires. Voltage correct. Ordered new element which can in 2 days. Installed-tested- problem solved. 2 scres connect element.

The stem of one of my burner switches broke off so I had to replace the switch.

  • Customer: John from Fulton, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.

electric bake element had a physicle break

  • Customer: Edward from Summit, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
First I removed the two screws that hold the element in place. Then I pulled the element out about 2 inches & disconnected the two wires, Then I removed the ground wire. I then wired in the new element ( this was the only tough part of the process, because I had a very tight space to work in- less than 2 inches.

Numbers on original stove top had become unreadable due to age and needed to be replaced

  • Customer: James from Montclair, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
I originally ordered the knobs that appeared to be an exact match for the ones on the stove top (Part # PS1515077). However those knobs are designed to fit on D post stems. I finally ordered PS48861 which are designed to fit double flat post stems which is what I have on my stove top. New parts fit perfectly. Remove old knobs put new ones on. Total repair time less than one minute. Part Select was great about getting the original parts and replacement to me quickly.

parts fine,

  • Customer: MARY from ELK RIVER, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
just inserted in to proper place

replaced the current warn-out grease filter

  • Customer: Joseph from East Greenwich, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
removed the old by pulling it out of track and replaced it with the new filter

The filter in the grill section of my stove fell apart.

  • Customer: Beth from Dunkirk, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.

the original grease filter was worn and falling apart

  • Customer: Barbara from Medfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.

I Destroyed My Grease Filter In The Dishwasher And It Just About Disintergrated.

  • Customer: Rosetta R. from Jamaica Plain, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 6 people found this instruction helpful
I just had to drop the grease filter into the slot. It took less than a second. But what I am really pleased with is that it took less than a day and a half to get the part. I ordered it on thursday morning. It was shipped on thursday afternoon and in my driveway by friday noon!!! Wow!!! How great was that!!!!!! The fastest service I've every had for anything!! Bravo!!!!!!!! To all your workers!!!!! Rrm
All Instructions for the 4875
76-90 of 141