484367D Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broke
2 of 2 people
found this instruction helpful.
-
Richard from COFFEYVILLE, KS
- Very Easy
- Less than 15 mins
-
Socket set
took out the old one, screwed in the new one. very easy.
Was this helpful?
Thank you for voting!
bake element burnt out.
2 of 2 people
found this instruction helpful.
-
james from WOOTON, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed screws,unplugged terminal leads,installed new one,back in business.
Was this helpful?
Thank you for voting!
Original terminal degraded and faulty
2 of 2 people
found this instruction helpful.
-
Robert from PRAIRIEVILLE, LA
- Easy
- 15 - 30 mins
-
Screw drivers
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto
... Read more
each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Read less
Was this helpful?
Thank you for voting!
Bottom oven element non-functional
2 of 2 people
found this instruction helpful.
-
Louis from GAINESVILLE, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal proc
... Read more
edures. Also good time to clean oven.
Read less
Was this helpful?
Thank you for voting!
the burner stop working
2 of 2 people
found this instruction helpful.
-
Anthony J from HAMMONTON, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Just followed the instructions
Was this helpful?
Thank you for voting!
Oven bake element failed.
2 of 2 people
found this instruction helpful.
-
Gerald from PALM COAST, FL
- Easy
- 15 - 30 mins
-
Nutdriver
I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.
Was this helpful?
Thank you for voting!
Element burnt out and cracked
2 of 2 people
found this instruction helpful.
-
Robert from LOUISVILLE, KY
- Very Easy
- 15 - 30 mins
-
Nutdriver
I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced th
... Read more
e new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!
Read less
Was this helpful?
Thank you for voting!
oven door not closing completely
2 of 2 people
found this instruction helpful.
-
David from BIRDSBORO, PA
- Very Easy
- 15 - 30 mins
older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.
Was this helpful?
Thank you for voting!
Heating element for a frigidaire stove top broke
2 of 2 people
found this instruction helpful.
-
Rebecca from ASHEVILLE, NC
- Very Easy
- Less than 15 mins
Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.
Great company. Makes it easy for me order.
Was this helpful?
Thank you for voting!
Bake element (bottom of oven) burnt through and snapped in two
2 of 2 people
found this instruction helpful.
-
Amber from CARLISLE, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this helpful?
Thank you for voting!
Bad element
2 of 2 people
found this instruction helpful.
-
david from PERRY, ME
- Very Easy
- Less than 15 mins
-
Screw drivers
Remove screws pull off wires and install new parts
Was this helpful?
Thank you for voting!
Burner not heating up.
2 of 2 people
found this instruction helpful.
-
Arlene from ERIE, IL
- Very Easy
- Less than 15 mins
Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.
Was this helpful?
Thank you for voting!
Old heating element broke
2 of 2 people
found this instruction helpful.
-
Paul from Ellenville, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated wi
... Read more
th another beer.
Read less
Was this helpful?
Thank you for voting!
Two burners did not heat
2 of 2 people
found this instruction helpful.
-
Conan from Moline, IL
- Easy
- 30 - 60 mins
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink ... Read more to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink ... Read more to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Read less
Was this helpful?
Thank you for voting!
Broiler element burnt out. It literally broke off & emitted white-hot sparks.
2 of 2 people
found this instruction helpful.
-
MG from ENCINITAS, CA
- Easy
- 30 - 60 mins
-
Screw drivers
First thing I did was turn off power to the range at the circuit breaker. The repair was generally easy with the exception that 1 screw holding the broiler element support was "welded" into the oven ceiling. I stripped the screw trying to get it out. Fortunately, I had a special tool that allows one to grip the outer edge of the screw w
... Read more
hile turning it --- and that's how I got it apart. Once the broiler element support was off, I removed 2 screws holding the broiler element itself to the oven wall and carefully pulled the broiler element out from the oven wall and detached the wire clips connecting the wires to the broiler element. I reattached the clips onto the new element and installed the new element back into the oven wall. I then reattached the broiler element support using a another screw (because I decimated the original one). I then turned the circuit breaker back on and turned the broiler on. Woila. My broiler works again! Special thanks to the people at this site who were very helpful in seeing to it I got the correct broiler element. The original ordered broiler element was delivered to the wrong address. The folks at this site sent me another one. To make a long story short, they saw to it I got the correct part. I highly recommend this site based on my experience with them.
Read less
Was this helpful?
Thank you for voting!