4809 Frigidaire Range - Instructions

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Turned off range/oven breaker. Opened the oven door. Removed two 5/16 hex head screws. Pulled bake element forward and removed the two slip on electrical connections from old bake element and put them on the new one. Replaced the two screws, closed the oven door, and proceeded to overhaul the kitchen faucet.

I unplugged the stove from the power plug in the wall. There are two screws at the back of the oven to hold the element in place. I removed the two screws. There are wire clamp inserts that attach to the element. Once the element was loose from the back wall of the oven, I gently pulled out the wire clamps. Removed the element. I lai ... Read more d the new element in the bottom of the oven and gently pushed the wire clamps into the new element. Re-attached the screws and put the power back into the wall and I was done. Easy, easy, easy. As for the drip pans, I pulled the element from the plug just under the stove top, cleaned the element and replaced the old drip pans with the new. Slid the element back into the plug and I was done.

Pulled out the old, and replaced. Very simple for a 62 year old woman! I cook a lot, being from the country, and Imwas so excited to get my burners fixed! Should have done it years ago! Thanks!

raise top of stove unplug burner plug in new one done

I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.

Thanks, PartSelect

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were re ... Read more ally stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to ... Read more play 18 holes of Golf!

Took out 2 screws unclipped the part put the new one on and i was done. Very easy fix .. Baked a cake right after to celebrate

We called a local repair shop and they told us that it would take a month to get our part and it would cost over $50 for it. We went online and found PartSelect.com. The part was here in less than one week and it cost less than $40. My husband pulled the stove out from the wall took a screwdriver and unscrewed the screws, slipped in th ... Read more e new part and screwed the new screws in. It took him 15 minutes to fix it and now my stove works better than it has in many years!

I UNPLUGGED the oven (very important), then I removed the two screws that hold the element in place, pulled the element out far enough to disconnect the two wires, plugged the wires on to the new element, pushed the new element back into place, and replaced and tightend the two screws. Finally, I plugged the oven back in.

Pulled control panel off front of unit and replaced switch wire for wire , went great because part sent was OME

Too dark to see, so left the power on so I cold use the oven light. Big mistake, shorted the fuse at the main box. No power in part of the house until finally figured out how to trip the fuse back on. Lesson learned. Never work on anything electrical without first turning off the power.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the new element, reassembled and SHAZAM. It worked. I am not good with electrical circuit testing etc. even though I know it must be easy so after reading many stories here, I decided to ... Read more start by replacing just the element and see if I got lucky. I did. No need to call expensive repairman.