480447F Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
3 of 3 people
found this instruction helpful.
-
Daniel from Falmouth, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven ... Read more has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Read less
Was this helpful?
Thank you for voting!
Bake elemen t shorted out.
3 of 3 people
found this instruction helpful.
-
LARRY from LEES SUMMIT, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers
Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.
Was this helpful?
Thank you for voting!
Broiler element burned out
3 of 3 people
found this instruction helpful.
-
Trisha from Shelbyville, TN
- Very Easy
- 30 - 60 mins
-
Screw drivers
Just took the old one out & put the new one in . Just a few screws to remove & put them back when replacing to new broil element , and were back up and cooking :)
Was this helpful?
Thank you for voting!
I forgot to remove something I had saved in the oven, planning to remove it before using the range.
3 of 4 people
found this instruction helpful.
-
Marilyn from Clearwater, FL
- Easy
- Less than 15 mins
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience
... Read more
with those in need of you services. Thanks. Marilyn Kasson
Read less
Was this helpful?
Thank you for voting!
element had been damaged
4 of 7 people
found this instruction helpful.
-
Merle from Towanda, PA
- Really Easy
- Less than 15 mins
I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.
Was this helpful?
Thank you for voting!
Bake Element caught on fire
4 of 7 people
found this instruction helpful.
-
Judy from Spencerville, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.
Was this helpful?
Thank you for voting!
Bake element bad, broiler element OK.
5 of 10 people
found this instruction helpful.
-
Gerry W. from Oxford, IA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from ... Read more a local dealer!
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from ... Read more a local dealer!
Read less
Was this helpful?
Thank you for voting!
Old heating element broke
2 of 2 people
found this instruction helpful.
-
Paul from Ellenville, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated wi
... Read more
th another beer.
Read less
Was this helpful?
Thank you for voting!
bake element burned out
2 of 2 people
found this instruction helpful.
-
Kenneth from Wantage, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into b
... Read more
ack wall of oven. Don't know what you would do then.
Read less
Was this helpful?
Thank you for voting!
Heating element for a frigidaire stove top broke
2 of 2 people
found this instruction helpful.
-
Rebecca from ASHEVILLE, NC
- Very Easy
- Less than 15 mins
Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.
Great company. Makes it easy for me order.
Was this helpful?
Thank you for voting!
Bad element
2 of 2 people
found this instruction helpful.
-
david from PERRY, ME
- Very Easy
- Less than 15 mins
-
Screw drivers
Remove screws pull off wires and install new parts
Was this helpful?
Thank you for voting!
The6" surface element I use the most broke. I then decided it was time to buy original replacement drop bowls, since the ones I had been buying never it correctly.
2 of 2 people
found this instruction helpful.
-
Vitoria from SANDY VALLEY, NV
- Very Easy
- Less than 15 mins
Actually, a child of average intelligence can do this. Just pull the surface elements, take the old drip bowls, install the new ones and re-install the surface elements, including the brand new one I received.
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner not heating up.
2 of 2 people
found this instruction helpful.
-
Arlene from ERIE, IL
- Very Easy
- Less than 15 mins
Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.
Was this helpful?
Thank you for voting!
Bake element (bottom of oven) burnt through and snapped in two
2 of 2 people
found this instruction helpful.
-
Amber from CARLISLE, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this helpful?
Thank you for voting!
Original terminal degraded and faulty
2 of 2 people
found this instruction helpful.
-
Robert from PRAIRIEVILLE, LA
- Easy
- 15 - 30 mins
-
Screw drivers
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto
... Read more
each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Read less
Was this helpful?
Thank you for voting!