480440F Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
element burned out
1 person
found this instruction helpful.
-
Nancy from Prosser, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
unfastened clip at back of oven w/screwdriver. Pulled out the plug, unplugged the element. Plugged in new element, pushed back into place, refastened clip to hold it in place at back of oven.. Done
Was this helpful?
Thank you for voting!
Bottom element had hot spots, very slow heating
1 person
found this instruction helpful.
-
Carl from PORT ST LUCIE, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
Turn off the power to the range. Remove oven racks. Remove the two screws and slowly pull the element out being careful not to pull the wires off. Remove the two wires then attach them to the new element. Push the element back in place, put the screws back in, turn on the power and turn on oven to make sure the problem is fixed
Was this helpful?
Thank you for voting!
Lower Heat element burned out.
1 person
found this instruction helpful.
-
Horace from CRUMPLER, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals befor
... Read more
e tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.
Read less
Was this helpful?
Thank you for voting!
Needed an additional rack
1 person
found this instruction helpful.
-
Gary from Darragh, PA
- Really Easy
- Less than 15 mins
Open the door and slide in the new rack.
Was this helpful?
Thank you for voting!
oven not heating
1 person
found this instruction helpful.
-
janet*hubbard from Old Town, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
slid the old one out and slid the new one in.turned the unit on and it works
Was this helpful?
Thank you for voting!
Oven would not heat up-
1 person
found this instruction helpful.
-
Charles from Hagerstown, MD
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Was this helpful?
Thank you for voting!
bake element burnt into
1 person
found this instruction helpful.
-
don from whiteville, NC
- Easy
- Less than 15 mins
-
Nutdriver
i removed the back panel removed two screws pulled the element out
Was this helpful?
Thank you for voting!
Element Was Sparking And Coal Hot Red
1 person
found this instruction helpful.
-
MIRANDA from INDEPENDENCE, KY
- Easy
- Less than 15 mins
-
Nutdriver
Unplugged oven, pulled out old element, reattached new one, making sure to be careful with wires, and put on as secure as possible, just like it was before. . . Very easy to fix
Was this helpful?
Thank you for voting!
Bake element broken
1 person
found this instruction helpful.
-
Richard from Campbell, CA
- A Bit Difficult
- Less than 15 mins
-
Nutdriver, Pliers
Removed screws. Tried to pull out old element but spade lugs on old element were bent at ninety degree angle. Once I figured that out I was able to manouver the old element out with the attached wires. Had to be carfull that the loose wires did not slip back ijn through the hole. Reaching in over the oven door was a but diffcult, but all-
... Read more
in-all the jobe was done in a few minutes.
Read less
Was this helpful?
Thank you for voting!
bake element had stopped working
1 person
found this instruction helpful.
-
lynne from pelham, NH
- Easy
- Less than 15 mins
-
Pliers, Socket set
My husband had recently moved out of our house so I was very nervous about trying this repair myself but it was actually very easy!!I ordered the part on Monday, it arrived on Wednesday and Wednesday night I was baking dinner in the oven!!
Was this helpful?
Thank you for voting!
bake element arched and caught fire.
2 of 4 people
found this instruction helpful.
-
Marie E. from Delray Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
i called Sears and ordered the element and they charged me 16.99 plus the part to ship the next day. after 1 week i called them and they said the part was on backorder. i then check with them each week almost a month and the part was still on back order, I asked if they could fix it faster if they came to the house, they informed me it w
... Read more
ould cost 65.00 for a repair person to see what part i needed and after that they would schedule m e for a repair when the part came in. meanwhile i could not use my oven. i happened to go on line and came up with your web site. i ordered the part and 2 days later my son installed it. my oven works great . your company is awsome.
Read less
Was this helpful?
Thank you for voting!
bake element burned up
1 person
found this instruction helpful.
-
charles from cartersville, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done
Was this helpful?
Thank you for voting!
Fried baking element
1 person
found this instruction helpful.
-
Jeff from wilmington, DE
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged stove, removed screws holding element In place. Pulled element forward exposing electrical ends. Removed connectors, re- connected ends to new element. Pushed element back into holes and reconnected the screws. Plug stove back in.
Was this helpful?
Thank you for voting!
Original Elememt went bad
1 person
found this instruction helpful.
-
Steve from Orefield, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.
The only real area for a potential problem is pulling the wire connectors thr ... Read more ough into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
The only real area for a potential problem is pulling the wire connectors thr ... Read more ough into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
Read less
Was this helpful?
Thank you for voting!
Baking element burned out
1 person
found this instruction helpful.
-
Richard from Aiken, SC
- Really Easy
- Less than 15 mins
-
Nutdriver
The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed t ... Read more he two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed t ... Read more he two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!
Read less
Was this helpful?
Thank you for voting!