4620 - Parts

This is a Genuine Manufacturer Approved replacement Belt used on Murray Lawn Tractors. This part is made out of Rubber and it is Sold Individually. This is the the Smaller Belt that drives Blades on your unit. Clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodical...Read morely and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Fist you would need to lower the mower deck to the lowest position • Then move the blade engagement lever to the Off position. • Roll the belt off the engine pulley from between the belt guide and pulley. • Remove mower deck by removing the bow-tie pins securing the left and right lift arms • Disconnect the blade engagement cable from the mower deck • Remove the bolts from the mower deck belt pulley covers and pull the covers off. • Loosen but don't remove the nuts on the top of the idler pulleys. • Install the new mower deck belt through the belt guides and around the pulleys. • Tighten the nuts on the top of the idler pulleys. • Re-Assemble the Deck

This centerlock nut, also known as a flange nut or hex nut flange is a manufacturer approved replacement part. It is 5/8 of an inch with 18 threads per inch. The nut is designed to secure the bolt or screw it is positioned on and prevent it from loosening during use. It has a series of ridges on the inside that allow it to grip the thread...Read mores of the bolt or screw and a flange at its base to provide a larger surface area to clamp on. Over time the lock nut may break or become stripped. Inspect all the centerlock nuts on your equipment as you may need to order more than one for your repair. To install a new nut, use your hands to thread it on and use a pair of pliers or a wrench to tighten it until it is securely held. Be careful not to overtighten the nut as this can deform the nut and wear down the threads that keep it secure. If you experience difficulties removing or tightening the nuts, use a centerlock nut tool or a cassette lockring tool instead. Note that this nut is sold individually.

This bolt is designed for use with various models of lawn and garden equipment and is a genuine OEM part. Featuring a square securing-area underneath the head for locking purposes, this bolt measures .31-inches in diameter and is 18 threads-per-inch. This bolt is made of high-quality metal and may require you to acquire multiple, depending on the use and location of installation for your equipment.

This durable pedal is an OEM direct from Murray which was designed for use with lawn tractors. Pedals can become worn down over time, requiring replacement. Please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. This part is sold individually.

This part is available individually and is made of plastic and metal. The limit switch connects to the interlock and helps to turn off the engine if there is a problem. A wrench might be required during the replacement of this part. It will require replacing if it becomes broken. This is a Murray, Snapper, and Simplicity replacement part directly sourced from the manufacturer for use in lawn tractors.

This hex bolt is sourced from the original equipment manufacturer. The bolt is designed to fasten two individual parts together in your lawn and outdoor equipment. It is made of steel to withstand harsh environmental conditions and measures 0.25 inches in diameter and 0.62 inches in length. The hex bolt gets its name from its hexagon-shap...Read moreed head, which makes it easy to grip with a wrench or socket. Before installing the new bolt, first clean the threaded hole where the bolt rests to remove any dirt or debris in the area. Once the area is clean you can place the bolt in position using your hands and tighten it using a wrench or socket. It is important not to overtighten as this could damage the area and the bolt. Sold individually.

This is an authentic manufacturer sourced replacement blade. It is commonly used on Murray lawn mowers/tractors. This blade can be used to mow, mulch and discharge grass. Over time blade would become dull or bent. This would cause uneven cuts and could damage the mower. This part is made out of metal and it is sold individually. To replace it you would need a wrench to remove the nut that secures the blade.

It is an authentic OEM sourced item which is specially produced for use with Murray lawn tractors. The spindle bearing goes between the washer and the cast iron axle and helps to reduce the friction. During the installation process, a screwdriver and a set of pliers might be needed to replace this part. It is made of plastic and will requ...Read moreire replacing if it becomes broken. This is available as an individual replacement part.

This Washer (.40.81 16g Flt) is a black, metal part, requiring a socket set to install. Installation is rated as "Easy". This washer can be used to provide a tight fit between connected components. It attaches onto the bell crank between the adjusting nut and cotter pin. Refer to your make, model and diagrams to check if this model is right for you.

This is an authentic OEM sourced replacement air cleaner filter which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this component is to ensure that the air supplied to the unit is free of dust and other harmful contaminants. Over time it may wear out and get...Read more clogged eventually requiring a replacement to maintain your equipment at peak performance. Keep in mind this high-quality pleated paper filter is sold individually.

This OEM part is a zerk fitting that is sometimes called a grease fitting, lube fitting, grease zerk, or Alemite fitting. It is a metal nipple that you connect a grease gun to, allowing you to lubricate the moving parts in your lawn equipment, usually on joints or bearings. This fitting is 1/4 inch wide, has 28 threads per inch, and a thr...Read moreeaded portion that is .256 inches long. If the fitting is broken, you may notice that your machine is moving sluggishly, or the fitting may appear cracked or clogged with debris. It is important to replace a damaged fitting right away, because if you do not, debris can prevent the fitting from accepting grease and the moving parts of your machine will wear out faster and eventually break down completely. To replace the fitting, you will need to use a wrench to remove it from your machine. Keep in mind that this replacement part is sold separately, so you may want to consider stocking up on fittings before you need them. Since the fittings on your machine wear out at the same rate, having a few extra on hand can save you time and hassle down the road.