4201 - Parts

This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually. NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.

Hold-down clips, also known as retaining, locking or fastening clips, are designed to secure and fasten specific parts within equipment, and the use depends on the type and model. This hold down clip is used to secure the chute of various models of snowblowers, and is sold as an individual OEM part, without any securing hardware. Made of ...Read morenylon, this clip secures to the chute with two screws and two washers. If you notice a wobbly or insecure chute resulting in excessive vibrations from the chute, check to make sure the clip is in-place before inspecting it for damage and ordering a replacement. To replace this clip, you will need to gain access to the chute, with either a screwdriver or wrench, and once you can access it, it is as simple as unscrewing the old clip and installing the new clip and rest of the assembly.

This screw is sold individually.

The bearing seal, also known simply as the seal, is a special seal for the bearings in your tiller. It attaches in the tiller housing, with the bearing and shaft, and over time it can become damaged due to fatigue and general wear. This part is made of rubber, is black in color, and is sold individually. Repairing the bearing seal will ...Read moregenerally be a medium-difficulty job, one that requires a screwedriver, socket set, wrench set, and hammer.

8 x 2.125 This wheel is for lawn mowers. Wear work gloves to protect your hands when installing this part.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This is a genuine manufacturer-supplied part which is specially designed for use with Bolens and Troy-Bilt snowthrowers. The part helps to secure the #1757824 Chute Crank Rod which is sold separately. It provides an identical replacement fo...Read morer a missing or a faulty swivel block that was installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality swivel block is made of durable metal and is sold individually.

This genuine OEM carriage bolt is used to secure various parts in lawn and garden outdoor equipment. The bolt has a round head with a square area underneath it that prevents the bolt from turning and coming loose when it is installed. The bolt shaft has a diameter of 5/16 inches, with 18 threads per inch and the threaded portion of the bo...Read morelt is 0.62 inches long. If the bolt is corroded, the threads are worn down, or the head is damaged or deformed, you will need to replace the bolt to keep your equipment parts secured and functioning efficiently. To replace the bolt, first remove the nut using a wrench or socket. Once the nut is removed, you can unthread the bolt. Insert the new bolt in position, thread the nut on and use a wrench to tighten it. Be careful not to overtighten the bolt to avoid damaging it or stripping the threads. This carriage bolt is sold individually.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This is an original part sourced directly from the manufacturer. This 13-ounce can of red spray paint was designed for use on a variety of Troy-Bilt and MTD equipment and is an identical match for paint needed for touch-ups. One can is included per order.