4189 - Instructions

I removed the four screws of the filter frame exposing the check valve (piston and nut assembly) . I unscrewed the old check valve and replaced it with the new one.

This is a great website. I ordered my part on Wednesday night and it arrived Saturday morning without paying any extra for shipping. Plus since I am a female, this website enabled me to easily and affordably make the repair myself without having to worry about a repair man trying to take advantage of someone that they think they can.
... Read more >
I first made sure that there was nothing stuck in the drain area inside of the dishwasher. That meant I had to bail out all the standing water and then unscrew the mesh cover from the bottom. Since there was nothing in there I ordered a new solenoid.

First I unplugged the dishwasher. Then I removed the screws with a screwdriver that held the bottom cover on the dishwasher. Once I could see the installed solenoid, I put together the pieces of the replacement solenoid that I bought so I was sure to install the new one correctly. That did not require any tools. Then I unscrewed the two screws that held the solenoid in place and removed the little metal ring from the shaft which was the last piece holding it in place. Getting that ring off was tricky. I ended up using a pair of tweezers to pull it off. After that I put the new part on and screwed it in with the two screws provided. The little metal ring went on much easier than the old one came off. I screwed the bottom cover back on and voila! my dishwasher was fixed.

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days ... Read more later i had the parts, and the next day I had a fully functioning leak free dishwasher.

Read about somebody else with the same problem and ordered the check valve. 4 screws off, twist out old valve, twist in new valve, 4 screws back in. Now dishes are see-yourself clean.

Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

22 Year old dishwasher . . . Not worth repairing I thought so I pulled it out to dispose of it. Before I did, I went online to see if any parts were still available. . . To my surprise partselect. Com had it all! My problem was a plugged chamber located on rear wall of unit. A 20 minute repair once the new part arrived. Part arrived ... Read more in 3 days but was broken inside of pkg. I called and the operator apologized profusely. . . She told me to keep the defective and explained my cc would temporarily be charged for replacement but as soon as they received a credit from supplier my credit will appear on my cc stmt. I had a replacement the following day. . . What a company!!!!

Pulled dishwasher out. Unscrewed 4 screws holding body valve, disconnected 2 hoses and replaced valve, put machine back together in reverse order.

First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure ... Read more the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to t ... Read more he motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

Remove old left and right corner tub baffles, make certain area where the new baffles are to be inserted is clean and free of any debris. Gently press new baffles in to each corner. Remove old gasket insert and replace with new. Tell wife the job was a three hour ordeal that require advanced skills to complete!

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

The small 4" gasket was missing from the machine, and the large gasket was bent and out of place. I ordered the small gasket and installed it into the groove, placing the end flaps behind the large gasket. The large gasket was questionable, but I did not replace it. It seemed OK after I snapped it back into the door groove. Once the g ... Read more askets were properly aligned, I carefully replaced the inside door panel and screws. No more leak!

First we got all the water out of the bottom of the dishwasher. Removed the old, melted drain solenoid. Very important - DO NOT THROW ANYTHING AWAY. The solenoid that removed was melted; however I had to reuse the springs, brackets and plunger from the old solenoid. I had to scrape and clean (with a solvent) the metal plunger to reuse it. ... Read more Once I got it cleaned up and re-used the old parts, mounting it was easy. However, getting that tiny lockwasher on the shaft was a real pain in the ass. Finally I got it together and it worked great.