41373 (ASTEPEU) LG Washer Dryer Combo - Parts

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test yo...Read moreur valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. ...Read moreBe sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.

The door lock assembly is a part for your washing machine and tells the washer that the door is closed and locked into place. If the switch has shorted out and not locking, it is no longer delivering the message to the machine and it will not latch into place. If you find that your door will not close, open, or start, it is more than like...Read morely an issue with the locker switch assembly. The switch is located behind the front panel. You will need to remove the gasket to reach the switch.

This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is broken, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is made of blue plastic, and is ap...Read moreproximately 4 inches wide, 4.5 inches long, and two inches tall. This is an OEM part made by the manufacturer.

This replacement water inlet valve is designed for use in washing machines to manage water flow during the cold water fill, bleach dispensing, and prewash cycles. It features a standard hose fitting inlet and three outlet ports—two angled 45 degrees to the right and one angled 45 degrees to the left—ensuring precise routing of water to de...Read moresignated compartments. Constructed for durability and compatibility with select models, this genuine OEM component helps maintain proper cycle performance and water distribution. Replacement is recommended if water fails to enter the machine correctly or if specific cycles are not functioning. Always disconnect power and water supply before installation.

This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose connects the dispenser assembly to the tub. Before beginning the repair, unplug the washer and turn off the water supply. You will need a Phillip...Read mores head screwdriver to complete this repair; a clamp tool can also be helpful. Remove the screws holding the lid of the washer in place, and take off the lid. Locate the dispenser hose and remove its clamps. Place the clamps on the new hose, using the arrows for a guide in positioning the clamps. Install the new hose and reassemble all other parts.

Upgrade your LG washing machine with this genuine OEM tub bearing. Designed specifically for LG rear tub models, this high-quality component provides support to the spin basket shaft at the tub, ensuring efficient operation. Please ensure to check the suitability of this part with your particular machine model. Prior to installing, rememb...Read moreer to unplug your washer and shut the water supply off for safety. It is recommended to wear work gloves while replacing this part. Elevate the performance of your LG washer with this reliable tub bearing.

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub sp...Read morein smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

This friction damper assembly in your washer stabilizes the tub or drum. It absorbs the movements and vibrations during the spin cycle to keep the machine steady and reduce noise. It connects the tub to the cabinet. If the assembly is broken, your washer may be excessively noisy or shaky. This genuine OEM replacement part is sold individually, and separately from the shock absorbers.

This part is the replacement spider, or washer spinner support, for your washer. It is triangular, with three arms, and it is made of metal. The washer spinner supports and spins the tub or basket while the washer is running. If you notice that your washer shakes or moves during operation, or if it is excessively noisy, you may need to re...Read moreplace the spider. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub sp...Read morein smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

This is a suspension spring for models of LG washing machines. This spring, along with the shock absorbers, is the entire suspension of the washing machine. If your washing machine is having spinning issues, or if you are noticing an excessive amount of banging, this spring may be damaged or worn out and in need of a replacement. Replacin...Read moreg this spring will require you to gain access to the interior of the washer cabinet. This spring attaches to the frame of the washer cabinet and to the tub of the washer itself. Since there are normally two springs in each washer, they will likely wear down at the same rate and if you are replacing one, it is normal to replace both. However, this spring is sold as an individual OEM part, so consider that before ordering.