41003 (ASTESEU) LG Washer - Parts

The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small f...Read morelat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test yo...Read moreur valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

This magnetic door plunger, also known as the magnet holder, is built for your washer. When you order this part, you will receive the plastic housing and a spring that goes with it. The magnetic door plunger attaches to the inner door panel of the washer. It holds the door open when the washer is not running, and allows the door and tub s...Read moreeal to dry. This prevents mold and mildew from building up. Occasionally, the plastic tabs on the housing can break, and when this happens the part will need to be replaced. You may also notice that your washer lid or door will not close; this can also be a sign of a damaged magnetic door plunger.

This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to the drain pump so the used water can properly empty from the tub. This part is made of rubber, is black in color and measures 13 inches long. ...Read moreBe sure to drain the excess water from the washer before completing this repair. This is an authentic OEM part that is sourced directly from the manufacturer.

This kit includes 1 shock absorber and 2 pins.

This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is broken, or if the detergent is not dispensed during the wash cycle, you may need to replace it. The dispenser is made of blue plastic, and is ap...Read moreproximately 4 inches wide, 4.5 inches long, and two inches tall. This is an OEM part made by the manufacturer.

This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the smal...Read morel door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.

This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made entirely of plastic. This part is used to hold the shock absorber on the washing machine. There is a pin used at the bottom and top of the shoc...Read morek absorber. This model is sold individually. If your washing machine is experiencing an above-average amount of shaking and moving this part may be the reason.

This is a suspension spring for models of LG washing machines. This spring, along with the shock absorbers, is the entire suspension of the washing machine. If your washing machine is having spinning issues, or if you are noticing an excessive amount of banging, this spring may be damaged or worn out and in need of a replacement. Replacin...Read moreg this spring will require you to gain access to the interior of the washer cabinet. This spring attaches to the frame of the washer cabinet and to the tub of the washer itself. Since there are normally two springs in each washer, they will likely wear down at the same rate and if you are replacing one, it is normal to replace both. However, this spring is sold as an individual OEM part, so consider that before ordering.

This is an outer seal clamp designed for use within LG washing machines. This clamp tightens and secures the gasket that seals the washer tub from the door. If your gasket is loose fitting and is not damaged or warped, this clamp is likely worn out and in need of replacing. This clamp is an OEM part and is made entirely of metal, with a s...Read moretrong tension spring in the middle. This outer seal clamp is sold individually and will require a set of pliers to replace.

This shipping bolt is an OEM part that holds the tub and basket of your washer steady during transport, stopping them from moving around and getting damaged. You will usually find these bolts at the back of the washer, screwed into the frame. This is sold individually, but keep in mind that most washers need two of these bolts.