4045 - Instructions

Pulled dishwasher out. Unscrewed 4 screws holding body valve, disconnected 2 hoses and replaced valve, put machine back together in reverse order.

The hardest part was figuring out how to disassemble the door to replace the baffles and door gasket. No pictures or clues on the internet or my owners manual. I figured it out myself and the rest was a piece of cake. When the 7 screws were removed, the door liner lifted right out and new parts fit right in.

Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t ... Read more o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions

I replaced the top filler tube. (The $65 price for the filler tube is outrageous. Glad I didn't have a service man fix it. With mark-up it would have cost me over $100 for a 3 foot plastic tube. Crazy!)

While I was add it, I replaced the corner tub baffles.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to t ... Read more he motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

I simply detatched the broken old roller and snapped in the new one. It was very simple and I did not need any tools.

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rag ... Read more s and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.

There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that an ... Read more d you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.

I made this replacement more dificult because I removed the old motor/pump earlier. Should have done it at the time I installed the new unit to be sure all hoses where installed correctly. I hooked the drain hose to the wrong port and when I started the dishwasher I found my error. Once I corrected the problem and started it again - th ... Read more e wash and drain cycles were perfect and there were no leaks.

I popped off the front track stops--pretty easy with a little twisting and slid the basket out. A little leverage with a screw driver and the roller axle slipped off easily. Popped the new ones on, slid the basket back into the track and popped the stops in place and the job was done in under 15 minutes.

Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.

The motor seized up on my 1990 GE Dishwasher
Repair would cost 360. Replacement about 600
I ordered the motor and pump from PartSelect for 137..44
Remover the under counter washer (it‘s very light) and removed the water and drain line and disconnected the power. Turned the washer on it’s top to access the motor and pump an ... Read more d removed the electrical plug in lines, and the clamps holding the pump on to the connections. Replaced it with the new motor and pump, reconnected the electrical plug ins, added an adapter hose part, tightened the original clamps then reconnected the water, drain and electrical connections and reinstalled the washer. All in about an hour, The only glitch was the grounding screw for the ground wire on the motor. The screw was too long to tighten. Substituted the original shorter ground screw from the old motor, and that worked fine. Only used 4 parts from the large assortment of parts supplied.
Immediately ran the washer through a cycle, all worked perfectly.

First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started ... Read more it back up. Eventually it did get going.