4035 - Instructions

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nea ... Read more rby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

First I opened the package and screwed the new dispenser cap into place.

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfie ... Read more d.

Simply screwed in new cap

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
... Read more />I was very happy the the service.
Donald Brown

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. ... Read more When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Pulled unit out of cabinet took two top screws out of spinner spray arm and put back together.Old sprayer was plugged up not letting wash go through.Thanks for helping me fix and not replace unit.Saved at least 400.

I already had the engine off cuz I was doing a tractor swap so I simply separated the crankcase which was very easy kept things clean and carefully reassembled worked great

dissembled ordered repair parts, piston ,upper case, rod, camshaft, seal kit, and motor maintenance CD
The camshaft first provided did not have the compression release device on it and the cam lobe position was all wrong for the model engine I had. .
Parts Select provided me with the proper cam Shaft. Removed engine from mowe ... Read more r (Scag Freedom Z) 15 minutes, drained oil, flipped upside down removed bottom case, removed wrong cam shaft, reinstall new valve lifters, camshaft with decompression release on it matching dots on crankshaft. Used paint brush to coat all parts heavily with motor oil.
Do not put sealant on case gasket,(it might change crankshaft end play), retorqued bolt in alternating pattern, placed nylon pipe tape on drain plug threads, and reinstalled engine on mower. It started instantly and ran extremely smooth with no oil burn or vibration.

I am very happy with the support and quick mshipping Parts Select provided..

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very ... Read more next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

Pulled washer out about 6" without disconnecting any hoses. This way i could use both hands from the left side & front after i took the kick plate off.

Unscrewed old one and installed the new one.

Put on a new cap.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching ... Read more the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

easiest way i found to do it was pull dishwashers out from under the cabnet... laided a pillow down in front of the door and turned it on the front side... the part was very easy to get to at this angle....could have done it in less then 5 minutes but took my time to double check everything to be safe....took a total of about 10 minutes.. ... Read more ... very happy now no longer need to vacume out the old dish water left at the bottom of the dishwasher...... i think most anyone could do this very easy....