40230128 General Electric Dishwasher - Instructions

The motor seized up on my 1990 GE Dishwasher
Repair would cost 360. Replacement about 600
I ordered the motor and pump from PartSelect for 137..44
Remover the under counter washer (it‘s very light) and removed the water and drain line and disconnected the power. Turned the washer on it’s top to access the motor and pump and removed the electrical plug in lines, and the clamps holding the pump on to the connections. Replaced it with the new motor and pump, reconnected the electrical plug ins, added an adapter hose part, tightened the original clamps then reconnected the water, drain and electrical connections and reinstalled the washer. All in about an hour, The only glitch was the grounding screw for the ground wire on the motor. The screw was too long to tighten. Substituted the original shorter ground screw from the old motor, and that worked fine. Only used 4 parts from the large assortment of parts supplied.
Immediately ran the washer through a cycle, all worked perfectly.

Since the pump and the motor was a single unit, I removed the assembly by disconnecting the electrical plugs and drainage connections. This was a very simple installation. I reversed the above steps, reinstalled the dishwasher and all worked out well.

First I removed the dishwasher from under the counter. I turned it onto it's side so I had access to the motor and pump underneath. I determined which version of the old pump I had. I removed the old part and easily installed the new motor/pump following the directions. It took a little while for the water to begin flowing when I started it back up. Eventually it did get going.

The repair went smoothly. There were actually instructions included with the parts, so that was nice. The only "gotcha" I found was that . . . after you take off the old food-chopper, you have unscrew the old impeller from the motor shaft. This was a bit difficult and you'll want some good pliers to do it. Don't worry about stripping where the food chopper screwed on-to, that part is attached to the impeller and there is a new one on the new impeller. When I re-installed everything onto the dishwasher, it rattled the first couple of times while the wear-ring was finding it's seat. Don't worry, that's normal. It went away by the third wash. I think I still have a small crack in the pump housing, though. The pump housing is two halves of molded plastic fused together along a seam, and I think the seam is starting to leak. It's about one drop every 45 seconds. I'm thinking JB Weld will fix it.

Once i had the dishwasher removed everything went as the instructions indicated except for the overflow switch.I removed the switch from the old bracket which is not required,just install the switch assy. to the new bracket and proceed as instructed. the total repair shouldn't take more than 1 hour if you don't make the mistake i made.I AM VERY SATISFIED WITH PRODUCT.
I HAD NEXT DAY DELIVERY AT REGULAR POSTAGE CHARGE.

I had hoped to be able to do the entire replacement at the floor level through the front panel without moving the dishwasher out of the cabinet. That turned out to be impossible because two of the machine screws holding in the old pump rusted and would not budge.
I did however manage to do the replacement by moving the dishwasher only 16 to 18" out of the cabinet so that I could work on more than one side. A word of advice: Once the pump is disconnected get it out of the house as soon as possible. It will continue to leak on your floor otherwise. No point in getting your pants, shirt and tools all wet.
The best part of this replacement came when I buttoned the whole thing back-up and ran it. This new pump was significantly less noisy than the old one making it possible to stay in the kitchen and actually have a conversation with someone. (My dog no longer leaves either.)
Would I do it again....you bet!

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

After disconnecting the supply and drain hoses I unscrewed the security screws and slid the unit out of it's space under the counter. I tipped the machine about 30-45 degrees to one side and examined the underside. I noticed a solenoid that appeared to control a valve leading to the drain tube. I cycled the washer through a wash cycle and noticed that the solenoid never activated. I removed the solenoid and found it filled with debris. I cleaned it out and reinstalled it, but it still did not function. I ordered the part from PartSelect.com because they had the clearest description of the part I needed. Delivery was quick and installation took only a few minutes. After hooking everything back up and sliding the machine back in place, it works like new.

Replaced with a new rinse aid fill cap.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.

I DID turn the power OFF at the breaker panel prior to starting the repair.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishwasher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!

Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had never done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.

First I opened the package and screwed the new dispenser cap into place.