EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XART73 Whirlpool Refrigerator - Instructions

All Instructions for the 3XART73
46 - 60 of 1083

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken Shelf Bracket
26 of 30 people found this instruction helpful.
  • Thomas from Leesburg, FL
  • Really Easy
  • Less than 15 mins
Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf
Was this helpful?
Thank you for voting!
Water dispenser not working, Ice dispenser chute icing up
27 of 33 people found this instruction helpful.
  • Jeff from Parchment, MI
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I removed the outer ice/water dispenser cover following directions I found on-line (push down and gently pry out at the bottom). I then removed several nut-head screws which were holding a plastic plate which had the door light and electric control wiring mounted in it. Behind that I found a broken tab on the Control Bracket which was w hy my water dispencer was not working and I found the chute door for the ice maker was chewed up which allowed warm air into the chute and was causing my ice build up problem. Replacing the Control Bracket was easy. Just note how things come apart. Putting the chute door in was a little more complicated, but again, note how things come apart and you should not have a problem putting it back together.
Was this helpful?
Thank you for voting!
refrigerator door wouldn't remain closed
27 of 34 people found this instruction helpful.
  • Thomas from Fairfax, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The plastic lower door closing cam was worn down. Replacing it was very simple: remove the top door hinge by unscrewing three nuts; lift the door off the lower hinge; unscrew and remove the lower door hinge; screw the new plastic lower door closing cam on to the new door hinge; screw the new lower door hinge; lift the door back on to th e lower door hinge; screw the top door hinge.
Was this helpful?
Thank you for voting!
broken meat and vegatable draw
25 of 28 people found this instruction helpful.
  • douglas g. from roanoke, VA
  • Really Easy
  • Less than 15 mins
a simple replacement
Was this helpful?
Thank you for voting!
the original auger was plastic and broke
25 of 28 people found this instruction helpful.
  • scott from Cocoa, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Pretty easy to replace..just take your time with the ice crusher but the teeth are labeled a..b..and c. This auger is steel so I should have no problems with this breaking. I received this item less than 24 hrs after I ordered it! On Christmas eve...Thanks to all of you
Was this helpful?
Thank you for voting!
motor coupling weld broken
24 of 26 people found this instruction helpful.
  • HAROLD from SPRING HOPE, NC
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed four screws from ice maker motor/light support.Then unplugged electrical plug from side of freezer.Used two slip joint pliers to remove coupler from motor shaft. installed new coupler to shaft hand tight as will tighten as motor is run.Then reversed tear down order.
Ice dispenser works better than when we first got the refrig erator
Was this helpful?
Thank you for voting!
Refrigerator door fails to close on its own like it is designed to.
23 of 24 people found this instruction helpful.
  • Jay from Oconomowoc, WI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
The design of this refrigerator door (it's a side-by-side) is somewhat unbelievable. The door is designed to hold things, yet when you do the weight of the door wears out the lower door cams. The cams are designed to "complete the door closing", i.e. when you gently push on the door the cam mechanism takes over. When the cams wear, the door fails to close. Note to others - you may mistakenly think that the failure of the door to close is related to the seal; it is not.

The repair is quite easy; remove the upper cover, using a not driver (socket), then remove the upper door bracket. Make sure you hold the door or have someone else hold it. After the fasteners are removed gently lift up on the door and remove it from the lower cam assembly. You will see two plastic cam pieces; one on the lower bracket and one on the door. Both need to be changed to effectively "renew" the door closing mechanism. Once the cams are replaced the door can be reassembled to the refrigerator.
Was this helpful?
Thank you for voting!
Ice Door would not close
26 of 33 people found this instruction helpful.
  • Frank from Sandy, UT
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I removed the Ice door front cover on freezer door. Found door pivot was broken. I installed door pivot bracket, and dashpot in kit. I used most of the kit to repair it. The door now works like new. Thanks for the right parts Frank
Was this helpful?
Thank you for voting!
Cracked Evaporation tray was leaking water on kitchen floor
26 of 34 people found this instruction helpful.
  • Jerrel from REDDING, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Socket set, Wrench (Adjustable)
I emptied refrigerator contents and tilted the refrigerator to the right so as to access the metal panel upon which the evaporation tray was resting. The metal panel is on the left side underneath the refrigerator and the evaporation tray is resting on the panel. I removed 4 screws that were holding the metal panel, pressed down on the panel, slid out the old, cracked plastic evaporation tray, inserted the new plastic evaporation tray, raised the metal panel to its original position, replaced the 4 screws, being careful not to pinched the water line that feeds the ice-maker. VOILA! Un-tilt the frig and re-stock it. It took a day for the temperature to stabilize, due to tilting, I think. New tray $45.
Was this helpful?
Thank you for voting!
Refrigerator door failing to close without being pushed shut
25 of 32 people found this instruction helpful.
  • Kenneth from Greeley, CO
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers
Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.
Was this helpful?
Thank you for voting!
in door water dispenser tube broken off 1.5 inches from end
23 of 27 people found this instruction helpful.
  • haig from La Quinta, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Wrench set
shut off water supply behind fridge then released trapped water pressure in the line at the dispenser. Locked off dispenser controls (push button switch). Removed nozzle retaining screw and pulled out nozzle approx. 3 in. to cut off tubing at black pipe so as to use the old pipe as a guide/pull (fish) for the new pipe by joining the end o f the new nozzle to the cut and of the old pipe with electrical tape.Then pulled the old pipe from bottom of fridge while simultaneously feeding/pushing new pipe from top. I had to remove lower grate on fridge to access the pipe on bottom. Remaining coupling connection on bottom was done by hand to avoid stripping plastic coupling.
Was this helpful?
Thank you for voting!
broken drawer
22 of 24 people found this instruction helpful.
  • Jason from Farmland, IN
  • Really Easy
  • Less than 15 mins
Put new drawer in fridge.
Was this helpful?
Thank you for voting!
ice distribution door broke
23 of 28 people found this instruction helpful.
  • David from Winston-Salem, NC
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.
Was this helpful?
Thank you for voting!
plastic door shelf was cracked & couldn't hold any weight
20 of 20 people found this instruction helpful.
  • Nancy from Hilton Head Island, SC
  • Really Easy
  • Less than 15 mins
looked up the model #, found your co. & ordered a new one Service was excellent, shipping reasonable; it was a pleasant surprise. I will tell my friends about your co.
Was this helpful?
Thank you for voting!
Ice dispensor motor would run but would not dispense ice at the door!
22 of 26 people found this instruction helpful.
  • Larry from Hague, ND
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
To get the coupler off the motor shaft I took two adjustable wrenches and slit the old coupler where it was cracked.The threads on the motor shaft were stripped closest to the motor.I took two thin washers and put them on the motor shaft so the new coupler would not turn down to where the threads on the motor were sripped.Since the thread s on the coupler are left hand they keep the coupler tight as the motor turns the dispenser auger to dispense the ice.I was a bit difficult to unplug the wiring harness but got it after we used a screwdriver to keep the tab bent down until the harness was unplugged.
Was this helpful?
Thank you for voting!
All Instructions for the 3XART73
46 - 60 of 1083