EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XARG49 Whirlpool Refrigerator - Instructions

All Instructions for the 3XARG49
46 - 60 of 1197

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Right front wheel broke
31 of 40 people found this instruction helpful.
  • Tony from Chicago, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Socket set
Definatly a two man job. I suggest you put a pad down to protect your floor. Remove the filter, grill, and bolts per instructions. Everything is straight forward. Move the frame back 1/2 to 1 inch then tilt the frig back on it's side about 4 inches. If the frame doesn't drop down, move it back until the front of the frame comes of th e front lip of the frig. Place a block under the frig lip NOT the frame and WATCH YOUR FINGERS. The wheel should be hanging down. Just pull out the pin, replace the wheel (make sure you have it facing the correct way) and tilt back and pull the blocks. Move the frig back in place and replace the bolts. Took me and a buddy less than 30 minutes.
Was this helpful?
Thank you for voting!
auger or ice crusher in ice container was broken an wouldn't dispense ice
30 of 38 people found this instruction helpful.
  • Willis from Belleview, FL
  • Really Easy
  • Less than 15 mins
nothing to repair, simply removed the old ice container and auger from the freezer and replaced with it with the new one.
Was this helpful?
Thank you for voting!
The light switch on the refridgerator broke - no light.
36 of 58 people found this instruction helpful.
  • David from Albany, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!
Was this helpful?
Thank you for voting!
The rubber piece around it was worn out
28 of 35 people found this instruction helpful.
  • Carmen from Albany, NY
  • Easy
  • 15 - 30 mins
We just had to find the trick to put it in where it would catch on and the rest was a piece a cake.

You had to put it in the groove where it would catch and snap it in place and the rest went in
pretty easy.
Was this helpful?
Thank you for voting!
REplaced ice maker
30 of 42 people found this instruction helpful.
  • M from Lafayette, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Replacement was very easy as new ice maker was identical to the old one. Took about 10 minutes.
Was this helpful?
Thank you for voting!
Broken Shelf Bracket
26 of 30 people found this instruction helpful.
  • Thomas from Leesburg, FL
  • Really Easy
  • Less than 15 mins
Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf
Was this helpful?
Thank you for voting!
broken meat and vegatable draw
25 of 28 people found this instruction helpful.
  • douglas g. from roanoke, VA
  • Really Easy
  • Less than 15 mins
a simple replacement
Was this helpful?
Thank you for voting!
refrigerator door wouldn't remain closed
27 of 34 people found this instruction helpful.
  • Thomas from Fairfax, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The plastic lower door closing cam was worn down. Replacing it was very simple: remove the top door hinge by unscrewing three nuts; lift the door off the lower hinge; unscrew and remove the lower door hinge; screw the new plastic lower door closing cam on to the new door hinge; screw the new lower door hinge; lift the door back on to th e lower door hinge; screw the top door hinge.
Was this helpful?
Thank you for voting!
the original auger was plastic and broke
25 of 28 people found this instruction helpful.
  • scott from Cocoa, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Pretty easy to replace..just take your time with the ice crusher but the teeth are labeled a..b..and c. This auger is steel so I should have no problems with this breaking. I received this item less than 24 hrs after I ordered it! On Christmas eve...Thanks to all of you
Was this helpful?
Thank you for voting!
Shelf support stub for crisper broke
24 of 26 people found this instruction helpful.
  • edna from las vegas, NV
  • Really Easy
  • Less than 15 mins
  • Pliers
I had read here from someone that fixed there shelf support stub and it was very loose, so I was trying to advoid that problem. It took me less then 5 minutes and my only tool was a pair of pliers. A short turn clock wise from the 9 on a clock to the 12 ( which is the top left corner ). then pull the broke shelf stub straight out. Put t he new shelf support in the same way you took the old one out and turn counter clock wise 1/4 or from 12 back to 9 and you should have a tight fit. I hope this helped.
Was this helpful?
Thank you for voting!
motor coupling weld broken
24 of 26 people found this instruction helpful.
  • HAROLD from SPRING HOPE, NC
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed four screws from ice maker motor/light support.Then unplugged electrical plug from side of freezer.Used two slip joint pliers to remove coupler from motor shaft. installed new coupler to shaft hand tight as will tighten as motor is run.Then reversed tear down order.
Ice dispenser works better than when we first got the refrig erator
Was this helpful?
Thank you for voting!
refrigerator was intermittently cooling because thermostat contacts burned away.
23 of 24 people found this instruction helpful.
  • Dennis from Westlake, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Turn off the fridge and unplug the power. Inside the refrigerator unit, remove two plastic panels extending from the front to the rear cooling vent by unscrewing two screws. Gently unhook the thermostat tube from the rear vent.

On the control panel, gently pry off the two control knobs and the front control panel. Remove fo ur screws to drop down the control assembly. Unplug the left electrical connector and unscrew the lever control arm being careful not to bend it. Disconnect the right side electrical connector and you can now remove the control unit to a table to easily work on it.

Undo two screws to remove the thermostat bracket. Undo two more screws to remove the thermostat assembly. Install the new thermostat and reverse the process just described. It takes about 15 minutes if you know what to do ahead of time. You will have to reuse the plastic tube that covers the thermostat sensing tube.
Was this helpful?
Thank you for voting!
End Cap bracket broken when shelf over-filled.
23 of 25 people found this instruction helpful.
  • JOEL from Boynton Beach, FL
  • Easy
  • Less than 15 mins
  • Screw drivers
Brackets rotated outward and lifted to disengage from door. Front metal strip removed from broken bracket. New bracket placed on shelf strip ends and replaced into door mount plastic. Hardest part was caused by manufacturer changing number of part and supplying it as a "kit" with both left and right bracket, as opposed to previously ma rking each end LS of RS and changing the configuration so that LS became RS. Joelle, in Customer Service was wonderful in figuring out the number change and sending me the correct part after I realized the originally ordered part was for the wrong side.
Was this helpful?
Thank you for voting!
Cracked Evaporation tray was leaking water on kitchen floor
26 of 34 people found this instruction helpful.
  • Jerrel from REDDING, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Socket set, Wrench (Adjustable)
I emptied refrigerator contents and tilted the refrigerator to the right so as to access the metal panel upon which the evaporation tray was resting. The metal panel is on the left side underneath the refrigerator and the evaporation tray is resting on the panel. I removed 4 screws that were holding the metal panel, pressed down on the panel, slid out the old, cracked plastic evaporation tray, inserted the new plastic evaporation tray, raised the metal panel to its original position, replaced the 4 screws, being careful not to pinched the water line that feeds the ice-maker. VOILA! Un-tilt the frig and re-stock it. It took a day for the temperature to stabilize, due to tilting, I think. New tray $45.
Was this helpful?
Thank you for voting!
Refrigerator came with house my daughter purchased and needed new seals. Refrigerator is 17 years old.
24 of 29 people found this instruction helpful.
  • Barb from North Royalton, OH
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver
First, I read your instructions on line about how to replace a refrigerator gasket and freezer gasket. We replaced both. The information was extremely helpful since we had never done this before. We then loosed a few screws at a time starting with the outside door corner and worked our way around, replacing the seal as we took off the old seal. Leaving the old seal on as we worked our way around gave us the clearance we needed to insert the new gasket behind the metal plate which holds the gasket to the door. Your easy to use web site made ordering easy and delivery was unbelievably fast. Thanks.
Was this helpful?
Thank you for voting!
All Instructions for the 3XARG49
46 - 60 of 1197