EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3VED Whirlpool Refrigerator - Instructions

All Instructions for the 3VED
121 - 135 of 1368

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
refrigerator door was making a popping noise when opening and closing
10 of 10 people found this instruction helpful.
  • Vincent D from Blackwood, NJ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Not being a handyman I found this job realtively easy.I took most of stuff off fridge door, to make door easier to handle. I then undid top hinge door screws, 3 of them, lifted door out., replaced 2 cams.When putting door back on fridge, you have to make sure door is in exact position and top hinge is lined up exactly, or door will contin ue to pop a little.It took me a couple of times to get top hinge lined up exactly.
Was this helpful?
Thank you for voting!
The piece that covered the light at the back of the fridge burnt a hole in the cover.
11 of 13 people found this instruction helpful.
  • Jennifer from Islandia, NY
  • Really Easy
  • Less than 15 mins
First I removed the cover...and then I slid the new piece in. It looks great and so easy a caveman could do it...lol
Was this helpful?
Thank you for voting!
The old gasket had broken in one corner
11 of 13 people found this instruction helpful.
  • James from Louisburg, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver
I loosened all the screws around the perimeter of the door and pulled the old gasket out. While doing this, the new gasket had been sitting in warm water so it would become more flexible. I then started at the top of the door sliding the new gasket under the retainer and worked my way down the sides and across the bottom. After this, I ti ghtened the screws a little at a time until they were all tight.
Was this helpful?
Thank you for voting!
Ice Door Leaking
13 of 19 people found this instruction helpful.
  • Steve from Metairie, LA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.
Was this helpful?
Thank you for voting!
Broken gooseneck on fill tube
10 of 11 people found this instruction helpful.
  • Thomas from Brunswick, OH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The gooseneck on the icemaker fill tube extends out beyond the back cabinet of the refrigerator, and is easily broken. Luckily, this part is a piece of cake to replace. You'll literally spend more time pulling out your fridge and cleaning out behind it then you will replacing this part.

Shut off water supply line, and turn of f ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.

Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.
Was this helpful?
Thank you for voting!
Crisper Pan Side Reales Had Cracked
10 of 11 people found this instruction helpful.
  • LEVY from HOUSTON, TX
  • Easy
  • 30 - 60 mins
I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem
Was this helpful?
Thank you for voting!
Broken tray
11 of 15 people found this instruction helpful.
  • Brian from Los Angeles, CA
  • Really Easy
  • Less than 15 mins
Remove old tray, replace with new tray.

Simple & easy.

Best part is I ordered on Monday & received on Tuesday!
Was this helpful?
Thank you for voting!
door was making a poping sound upon opening and closing
10 of 12 people found this instruction helpful.
  • Tony from Mesquite, NV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Socket set
First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.
Was this helpful?
Thank you for voting!
socket melted with bulb in it.
12 of 18 people found this instruction helpful.
  • martin l. from JACKSONVILLE,, IL
  • Really Easy
  • Less than 15 mins
plastic warped in ,spaced out and, the socket snapped back in place.
Was this helpful?
Thank you for voting!
auger blades broken
11 of 15 people found this instruction helpful.
  • Michael from Ponchatoula, LA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed ice bin then pulled front cover with nut driver . Pull small rod from side ( one screw holding rod and spring). Pull auger out. Take plastic nut off end ( CLOCKWISE) LEFT HAND THREAD. Keep all ice crusher blades in order when you pull them off. Install new auger and reverse steps. web site has exploded view. It looks difficult but it isn't.
Was this helpful?
Thank you for voting!
Would not dispence ice
14 of 24 people found this instruction helpful.
  • Mike from Chickasha, OK
  • Easy
  • 15 - 30 mins
  • Socket set
Removed screws from front of ice container,replaced drum.
The hardest part was assembly of ice crusher,lucky the arms were lettered as to how they went back together.
Was this helpful?
Thank you for voting!
Ice Door broken letting warm air into Ice Maker system which kept freezing up.
25 of 57 people found this instruction helpful.
  • Anthony from Magnolia, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)
Was this helpful?
Thank you for voting!
Compressor would not kick on automatically
10 of 12 people found this instruction helpful.
  • Robert from Brooklyn Center, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I removed the two screws that were readily in view. I then figured out the there was a faceplate which I was able to pry off after removing the temp control knobs. The temp control unit was easily accessible and was held by two screws which I removed with the nut driver. The only difficult part was replacing the plastic tubing which co vered the sending unit.
Was this helpful?
Thank you for voting!
part of a freezer support bracket was missing
9 of 10 people found this instruction helpful.
  • peter from saint augustine, FL
  • Really Easy
  • Less than 15 mins
I wasn't sure the kit included the part I needed from the pictures, but it did. The part slipped over the flat plastic bracket attached to the right freezer wall and the shelf fit over it. No tools required.
Was this helpful?
Thank you for voting!
Severed/Rusted Support Shelf Stud
9 of 10 people found this instruction helpful.
  • Chris from Pensacola, FL
  • Really Easy
  • Less than 15 mins
  • Pliers
Easy as cutting through warm butter. Just grabbed the base of the broken stem flush with the wall of the fridge using the wide-angle setting of a normal pliers, and twisted it out. Left over was a hole to insert the replacement stem. Inserted stem, twisted clockwise into place, and done. Much better design than other units I've worked on becvause the replacement part has stout-gauge wires that, when new stem is twisted into place, "locks" it in so you don't need to reinforce it, acting somewhat like an anchor screw on the wall for hanging a picture. Thanks for the perfect part!! Service and delivery are excellent.
Was this helpful?
Thank you for voting!
All Instructions for the 3VED
121 - 135 of 1368