3ET2 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Raplaced switch
5 of 9 people
found this instruction helpful.
-
Winston A from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
broken self
4 of 6 people
found this instruction helpful.
-
JAMES from HILTON, NY
- Very Easy
- Less than 15 mins
This was a simple install. I just replaced the glass shelf on the sliding shelf bracket.
Was this helpful?
Thank you for voting!
Installed new glass crisper
3 of 3 people
found this instruction helpful.
-
Rebecca from WEST JORDAN, UT
- Very Easy
- Less than 15 mins
Open your door as far as it will go. Line it up with the plastic holder should just slide into place.
Was this helpful?
Thank you for voting!
Drawer broken
3 of 3 people
found this instruction helpful.
-
Terry from PLAINVILLE, CT
- Very Easy
- Less than 15 mins
Replaced the drawer
Was this helpful?
Thank you for voting!
Installing old ice maker in new freezer
3 of 3 people
found this instruction helpful.
-
Harry from Ten Mile, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside.
... Read more
Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.
Read less
Was this helpful?
Thank you for voting!
Fan motor
3 of 3 people
found this instruction helpful.
-
Bonnie from DETROIT LAKES, MN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove bottom of freezer by sliding out the gaskets on each side.
Remove back of freezer. 6 screws.
Remove fan cover. 4 screws.
Remove fan. 3 wires to disconnect. 2 screws to take out.
Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws.
... Read more >Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.
Remove back of freezer. 6 screws.
Remove fan cover. 4 screws.
Remove fan. 3 wires to disconnect. 2 screws to take out.
Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws.
... Read more >Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.
Read less
Was this helpful?
Thank you for voting!
Compressor making excessive noise
5 of 9 people
found this instruction helpful.
-
chester from Tampa, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled
... Read more
the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
gasket was cut and ripped
3 of 3 people
found this instruction helpful.
-
Herbert from NIAGARA FALLS, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one
Was this helpful?
Thank you for voting!
freezing everything
3 of 3 people
found this instruction helpful.
-
Darcie from VINELAND, NJ
- Difficult
- 30 - 60 mins
Removed old gasket. Wiped everything down. Popped in new gasket.
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Sa ... Read more ved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Sa ... Read more ved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
Read less
Was this helpful?
Thank you for voting!
Fan was making alot of noise
4 of 6 people
found this instruction helpful.
-
JERRY from ALBION, AL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
I removed all the shelves and the back shelf hanger. Removed two screws on the back plate.Pulled it out.Removed the screws that hold the fan housing. Pulled it out so I could write down the three wires color and location.Unpluged them.Removed the old fan and installed the new one.and put everthing back together.
Was this helpful?
Thank you for voting!
Noisy freezer evaporator fan motor
4 of 6 people
found this instruction helpful.
-
Lloyd from Long Beach, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed the shelves from the freezer and the brackets holding it along with the covers for the light and plate for the ice maker (we don't have one). Pulled the ground wire from the tab off the port for the ice maker. Removed back plate exposing the fan motor and then the 4 hex screws holding on part #23 of the diagram which the fan mot
... Read more
or is mounted to. Flipped it over, unscrewed the 2 hex screws from the fan motor mounting and removed it. Removed and replaced 3 wire connectors on new fan motor. Installed new fan motor and new grommets but used the old screws because the provided screws were larger. Pushed the new fan on to the motor shaft. Reassembled. Half hour most.
Read less
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people
found this instruction helpful.
-
Jane from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80..
... Read more
.would have been at least $100 to have a repair person come to the house!
Read less
Was this helpful?
Thank you for voting!
Divider front of fridge hot to touch Condenser fan not working
3 of 4 people
found this instruction helpful.
-
John from Holden, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away
Was this helpful?
Thank you for voting!
Ice maker motor excessive slip (essentially worn out) & contacts were worn
3 of 4 people
found this instruction helpful.
-
Richard from Blue Ridge, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
1 removed bottom off old ice maker (3 hex screws) and ice drop shield (white plastic ice flips over into ice holder, old unit had different drop angle, see how described below, but I just musled it off the old unit) 2 removed "ice sensing bar off new ice maker and rotated mechanical sensor to on (leatherman tiny flat head) 3 removed end
... Read more
cap from new ice maker, then loosened to large screws (Phillips, leatherman) for motor unit cover. This allowed removal of ice drop shield on new unit (two tabs, one at each end). 4 removed ice drop shield and installed old ice dropshield on new unit 5 tightened two endcap screws (Phillips/leatherman) and reinstalled end cap 6 installed old bottom unit/tray on new ice maker (3 screws) 7 ensured wiring matched and routed plug properly 8 installed unit slides in 9 plugged unit to existing plug 10 installed old wiring shield (1 hex screw). Waited two hours to verify water valve worked properly, although IR codes did indicate "okay". Machine has been making ice and IR sensor shuts it off properly. So far a success. I have many spare parts if I need to do further repairs including a new water solenoid. Only saying it was a bit difficult because of the parts exchange, in actuality for me it was really easy.
Read less
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!