EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3ET18Z Whirlpool Refrigerator - Instructions

All Instructions for the 3ET18Z
46 - 60 of 318

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Leakiong water from the freezer compartment into the lower refrigeration compartment
7 of 12 people found this instruction helpful.
  • Mark from indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
After unplugging the appliance, I unscrewed the screws in the bottom and the back of the freezer compartment and un-clipped the connector for the ice machine, which i do not have installed. I clipped the pink and brown wires and replace the switch with the new switch. unfortunately, the appliance is still dripping water from the freezer c ompartment. It worked for a couple of days then stopped working. Still looking for a true FIX.
Was this helpful?
Thank you for voting!
Broken glass shelf for top of crisper
5 of 6 people found this instruction helpful.
  • Tom from SHEBOYGAN, WI
  • Very Easy
  • Less than 15 mins
Part fit perfectly glass dropped right in
Was this helpful?
Thank you for voting!
Crisper Drawer Rail Broken
4 of 4 people found this instruction helpful.
  • Tom from DESTIN, FL
  • Really Easy
  • 15 - 30 mins
Removed crisper drawers removed glass shelf installed Rail.
Replaced glass shelf then installed crisper drawers.
Was this helpful?
Thank you for voting!
Gasket wouldn’t hold door shut.
4 of 4 people found this instruction helpful.
  • Patti from GARNEILL, MT
  • Difficult
  • 1- 2 hours
NO DIRECTIONS CAME WITH GASKET! Project failure as gasket tore on a corner. For the price of this gasket, I was DISAPPOINTED. Door is being held shut with a childproof strap.
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people found this instruction helpful.
  • Dave from Manchester Center, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
Was this helpful?
Thank you for voting!
Light in my refrigerator didn't work.
5 of 7 people found this instruction helpful.
  • Joseph from Byron Center, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Was this helpful?
Thank you for voting!
Lost shelf support bracket
4 of 4 people found this instruction helpful.
  • DAVID from LAFAYETTE, LA
  • Really Easy
  • Less than 15 mins
Ordered shelf support stud kit. Product was promptly delivered, and contained the parts as shown on website. Took longer to open the package than to replace the missing shelf support bracket. No problems. Would order from them again.
Was this helpful?
Thank you for voting!
Refrigerator light would not turn on.
5 of 8 people found this instruction helpful.
  • Suzanne from STERLING HTS, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Was this helpful?
Thank you for voting!
Filler tube broken and old tube frozen over
4 of 5 people found this instruction helpful.
  • Alan from Chino, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube ( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?
Was this helpful?
Thank you for voting!
Broken Door Shelf Suport
4 of 5 people found this instruction helpful.
  • Charlie Jeanne from Lafayette, IN
  • Really Easy
  • Less than 15 mins
Our trusty fridge is so old that I couldn't find any replacement parts on the manufacturer's website. Thanks to PartSelect, I was able to keep narrowing down my request until I found an illustration of a part that matched my dimensions exactly. Delivery was FAST. Within 10 minutes I had the old duct-taped shelf support gone and a perfec t replacement part installed. Looks like new! I may be a 67-year old grandmother, but a pro couldn't have done it any faster or better. Thanks so much for your excellent website and prompt delivery!
Was this helpful?
Thank you for voting!
Lights not working some times
4 of 5 people found this instruction helpful.
  • Harry from COLUMBIA STA, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed old switch and installed new - but did not solve problem
Was this helpful?
Thank you for voting!
Freezer froze and refrigerator wet
5 of 8 people found this instruction helpful.
  • Patricia from Marengo, OH
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio
Was this helpful?
Thank you for voting!
Broken filler tube at threaded connection
4 of 5 people found this instruction helpful.
  • Matthew from Phoenix, AZ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out and it works good as new!
Was this helpful?
Thank you for voting!
Installing old ice maker in new freezer
3 of 3 people found this instruction helpful.
  • Harry from Ten Mile, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.
Was this helpful?
Thank you for voting!
Compressor making excessive noise
5 of 9 people found this instruction helpful.
  • chester from Tampa, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Was this helpful?
Thank you for voting!
All Instructions for the 3ET18Z
46 - 60 of 318