EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

39541 General Electric Refrigerator - Instructions

All Instructions for the 39541
106 - 120 of 592

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
2 of 2 people found this instruction helpful.
  • David from CLIFTON, NJ
  • Really Easy
  • 30 - 60 mins
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this helpful?
Thank you for voting!
Door Not Closing Tightly + Staying Open
4 of 8 people found this instruction helpful.
  • Jeff from Venice, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Sl id the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )
Was this helpful?
Thank you for voting!
no problems
2 of 2 people found this instruction helpful.
  • Sharon from Kennewick, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First removed the old sliders, then screwed in the new sliders, replaced all four within minutes.
Was this helpful?
Thank you for voting!
Closing cam disintegrated
2 of 2 people found this instruction helpful.
  • Larry from Renton, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed everything from the refrigerator door. Removed the screw holding the cover over the top hinge. Removed the two (8mm) bolts holding the top hinge to the refrigator. Removed the door. Removed the plastic grill/cover and the two (8mm) bolts from the lower hinge assembly. Installed the new hinge assembly. Replaced the closing c am (included in the hinge assembly kit) on the bottom of the door. Put the door back on the lower hinge. Installed the upper hinge. Adjusted the door and tightened the bolts on the upper hinge, and replaced the hinge cover. Done!
Was this helpful?
Thank you for voting!
The drawer rails had broken causing the drawers to drag
2 of 2 people found this instruction helpful.
  • Barry from Grenada, MS
  • Easy
  • 15 - 30 mins
  • Screw drivers
Each rail required removing two screws which were used to install the new rail. Each one took about 5 minutes however cleaning the recesses was the most effort.
Was this helpful?
Thank you for voting!
worn/broken cam , door doesn 't self close
2 of 2 people found this instruction helpful.
  • Charles from Franklinville, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .
Was this helpful?
Thank you for voting!
Slide rail was missing when we bought house
2 of 2 people found this instruction helpful.
  • Joe from Lawrenceville, GA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Got the part in and needed two screws to installed on left side. Service was great on the part as it was delivered in 3 days from the time we ordered. Thanks for the quick service
Was this helpful?
Thank you for voting!
Severe Ice Build Up, But Freezer Temperature Inadequate
2 of 2 people found this instruction helpful.
  • Randall from Ashburn, VA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I followed the troubleshooting instructions for freezers with ice build-up. First defrost the freezer. This makes a huge mess. The tray for water buildup is very small. I suggest covering the hole so no water gets to the tray and collecting the water as it melts in the freezer. (DO NOT pry the ice off with a knife. I did that when I was 1 4 and punctured the freon lines.) After the ice was gone inside the freezer, I removed the back panel of the freezer (a pair of 5/16" nuts on the bottom and a pair of #2 phillips screws at the top). The panel will then just pull straight out. Make sure the ice has melted from behind the panel as well before testing any of the components.

First component to check is the defrost timer. Pretty straight forward, using the instructions on the PartSelect home page and a multi-meter (looking for continuity or the lack there of). You need to remove it and check it out of the fridge. In my case the defrost timer worked correctly (bummer since it was much cheaper than the defrost heater kit). Next step was to test the Defrost Heater. I used a common since approach which was not mentioned in the instructions. I manually turned the defrost timer until it clicked. Then I put my hand next to the glass tubes that incased the heater elements. They did not get hot. I then turned the defrost timer until it clicked again. Again, the heater elements did not get hot. Since there are only two setting on the timer, it means the defrost heater was broken. If you can hear the refrigerator/freezer running, then you are not in defrost mode. Turn the thermostat for another click. All noise will stop...and heat should be found at the tubes (behind 6" thin tin covers), if they are functioning.

Removing the defrost heaters and thermostat was simple. There are four #2 screws (2 on each assembly). The thermostat is just clipped on. It is impossible to put the defrost heater assembly in wrong. Put the panel back on and your ready to go. The 30-60 minutes is not repair time but de-ice and repair time. I used a space heater to speed up the de-ice process.
Was this helpful?
Thank you for voting!
Refrigerator contents began to freeze up
2 of 2 people found this instruction helpful.
  • Andrew from Jefferson, ME
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I first rolled out the refrigerator, unplugged it, and emptied the freezer contents into a cooler.

Then removed the shelving (side by side freezer / refrigerator) and the four screws holding the back panel.

The coil and defrost heaters were covered with ice, so the paint heat gun made quick work of defrosting them.