3954 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light kept blinking on and off never same way
2 of 2 people
found this instruction helpful.
-
michael from CENTRALIA, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends
Other Parts Used:
Was this helpful?
Thank you for voting!
door hinge
2 of 2 people
found this instruction helpful.
-
Steve from BRANDON, MS
- Very Easy
- Less than 15 mins
-
Nutdriver, Socket set
put block of wood under the door, removed old hinge and installed the new one. about 15 minutes
Was this helpful?
Thank you for voting!
lower door hinge worn
2 of 2 people
found this instruction helpful.
-
Max from TUCSON, AZ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Socket set
I replaced both lower hinges without removing the doors. First a couple of observations. The hinge kit consists of two parts; the lower part (bolted to the case) consists of an “L” bracket with a plastic cam, and the upper plastic cam (attached to the door). For some reason the upper cam is available as a separate part . If both cams are
... Read more
plastic both are worn out. Don’t bother ordering the individual cam. If one hinge is worn out the other probably isn’t far behind. Consider replacing both at the same time. Examine the door check. It is an inverted “T” shaped bracket bolted to the door that also holds the door cam. The crossbar of the T are metal tabs that check the door swing. Way too fragile IMO. On mine the refrigerator side was cracked and broke off when I removed it. Since the stops are the same right and left. I just swapped them when I replaced the hinges. Saved $22. Replacing the hinges without removing the doors. {Warning if this technique goes wrong you will be stuck with a loaded door you can’t open.} Remove the vent grill. Stack three 2x4’s along the bottom of both doors ( 26” is about right ). Shim the door(s) up to compensate for the cam wear. About 1/8”) Use a 5/16 socket to remove the hinge from the case. Pay attention to placement of the shims and spacers. Then remove the door cam and stop bracket. Install the new door cam. Leave the screws a little loose. Replace the lower hinge and tighten the screws. Do both sides. Then carefully remove the shims and 2x4’s. Finish tightening the door hinge screws. Check the door swing. I used this technique twice. One to replace the refrigerator side hinge, then again to replace the freezer side hinge and swap the door checks. There were no problems and I saved the hassle of unloading and removing the doors.
Read less
Was this helpful?
Thank you for voting!
Original evaporator fan (31 years old) was making a lot of worn bearing noise
2 of 2 people
found this instruction helpful.
-
T from SOUTHBURY, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Empty freezer;
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.
I did have to use the wire extensions ... Read more that were included as the replacement motor had the electric connections in a different location from the original motor.
Overall, this was an easy replacement.
Remove shelves and ice trays;
Unscrew and remove the rear vertical panel;
Unscrew and remove fan housing;
Unscrew and remove fan from fan housing;
Fan blade slides off the motor shaft without tools.
Reverse order to reassemble with new fan motor.
I did have to use the wire extensions ... Read more that were included as the replacement motor had the electric connections in a different location from the original motor.
Overall, this was an easy replacement.
Read less
Was this helpful?
Thank you for voting!
The Refridgerator and Freezer were not cooling.
2 of 2 people
found this instruction helpful.
-
Frank from VERO BEACH, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Installing the part repaired the fridge and freezer immediately.
Was this helpful?
Thank you for voting!
freezer stoped freezing
2 of 2 people
found this instruction helpful.
-
paul from ENDICOTT, NY
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE
... Read more
OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.
Read less
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
a fan blade broken causing it to make a loud noise
3 of 5 people
found this instruction helpful.
-
Marnie from Denver, CO
- Really Easy
- Less than 15 mins
-
Pliers
we took off the old one and replaced it.
Was this helpful?
Thank you for voting!
freezer too cold and refrigerator not cold enough because fan not working
2 of 2 people
found this instruction helpful.
-
Ann from LAPORTE, PA
- Easy
- 30 - 60 mins
-
Nutdriver
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and r ... Read more ed wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and r ... Read more ed wires clipped from the old motor. Then reinstalled.
The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Read less
Was this helpful?
Thank you for voting!
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
2 of 2 people
found this instruction helpful.
-
David from CLIFTON, NJ
- Really Easy
- 30 - 60 mins
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this helpful?
Thank you for voting!
Door Not Closing Tightly + Staying Open
4 of 8 people
found this instruction helpful.
-
Jeff from Venice, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Turned off water to ref , removed bottom kick plate , got a towel and disconnected the water line plastic fitting and un screwed the (2) tube clamps un screwed the coupling and ((carefully )) slid out the tube from the compression ferrels ! ( Be careful and do not break or distort them + remember exactly the order they are removed ! Sl
... Read more
id the protector spring shroud from the plastic tube , took ogg the top hinge cover then remover the top hinge . Carefully lifted the door off feering the plastic tube through the bottom hinge with my foot ! Got the door off removed the bottom hinge + put the new on on, then removed the door cam which was broken on the bottom of the door , lifted the door up and carefully fed the water line through the new bottom hinge . Attached the top hinge and reassembled the rest same as I had dissambled it . Turned on water ( checked for leaks ) ! All working 100% a-ok ! This company is the best ! Ordered the part at 1 pm and had the part at 2 pm the following day many thanks : )
Read less
Was this helpful?
Thank you for voting!
Light out
2 of 3 people
found this instruction helpful.
-
Jodi from Benton Harbor, MI
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $
... Read more
120 service call.
Read less
Was this helpful?
Thank you for voting!
Light would no longer turn on
3 of 6 people
found this instruction helpful.
-
paypal_shipping_address from Ripon, CA
- Really Easy
- Less than 15 mins
-
Pliers
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this helpful?
Thank you for voting!
Needed a new door module
2 of 3 people
found this instruction helpful.
-
Marc from Hollywood, FL
- Really Easy
- Less than 15 mins
Fit perfectly, took 2 seconds to install.
Was this helpful?
Thank you for voting!
Refrigerator was not cooling
2 of 3 people
found this instruction helpful.
-
Jeffrey from Statesboro, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
The refrigerator was no longer cooling and it was suggested by my father that it could be our defrost timer as he has owned many Hotpoint refrigerators in his lifetime and he said the defrost timer was always the problem he had with them when they were not cooling properly. I removed the cover and unplugged the defrost timer, ordered a n
... Read more
ew timer through this website and installed it by plugging it where the old timer was, replaced the cover and plugged the refrigerator back in. The refrigerator is now cooling again and just in time for Christmas.
Read less
Was this helpful?
Thank you for voting!