38HY Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not work
0 of 2 people
found this instruction helpful.
-
george from San Antonio, TX
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench set
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!
Was this helpful?
Thank you for voting!
gasket was leaking heat from oven
2 of 12 people
found this instruction helpful.
-
NORMAN W from Waleska, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
removed old and installed new
Was this helpful?
Thank you for voting!
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
-
Ann from Schertz, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you c
... Read more
an find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat on Back Cycle
-
Jeff from Thousand Oaks, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resi
... Read more
stance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.
Read less
Was this helpful?
Thank you for voting!
oven temperature only goes to 275 degrees even when set higher; broiler works
-
Anne Marie from Huntingdon Valley, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small
... Read more
opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.
Read less
Was this helpful?
Thank you for voting!
change oven sensor
-
Lloyd from Eau Claire, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed provided video
Was this helpful?
Thank you for voting!
Fan runs continually ,door locked,error code f2,f3,f7
-
John from Dacula, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with m
... Read more
atched harness /.connection, installed 2 screws ,turned on breaker.
Read less
Was this helpful?
Thank you for voting!
Had code F1 and F3 on my oven. Oven wouldn't heat.
-
Cindy from Polson, MT
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this helpful?
Thank you for voting!
Oven would not heat up properly to set temperature
-
Max from Bothell, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced wi
... Read more
th a new one.
Read less
Was this helpful?
Thank you for voting!
temperature varied in oven.couldn't set
-
tom from winter haven, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair
Was this helpful?
Thank you for voting!
Oven randomly turned off and locked
-
Robert from homilton, MT
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replace the oven sensor per the excelent easy video you provided
Was this helpful?
Thank you for voting!
F-4 Code, oven wouldn't heat
-
Gary from San Jose, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding th
... Read more
e wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.
Read less
Was this helpful?
Thank you for voting!
The oven was not heating up to temperature
-
Max from Bothell, WA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electroni
... Read more
c clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards
Read less
Was this helpful?
Thank you for voting!
Broken Door Spring
-
Matthew from Chippewa Falls, WI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to r
... Read more
eplace the springs. This job was very simple and easy.
Read less
Was this helpful?
Thank you for voting!
Oven would not program and would shut down
-
Sreve from Deland, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and i
... Read more
n reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.
Read less
Was this helpful?
Thank you for voting!