38HY Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people
found this instruction helpful.
-
Paul from Foley, AL
- Really Easy
- Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri
... Read more
dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Read less
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people
found this instruction helpful.
-
Sharon from Yacolt, WA
- Really Easy
- Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Other Parts Used:
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people
found this instruction helpful.
-
Barbara a from Huntington, NY
- Really Easy
- Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
Replacement of broil element in wall oven
4 of 4 people
found this instruction helpful.
-
David from San Rafael, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw d
... Read more
river is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Read less
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people
found this instruction helpful.
-
Terry from Mountain City, TN
- Really Easy
- Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people
found this instruction helpful.
-
Trace from Ofallon, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces
... Read more
of sheet metal back on and plugged in the oven.
Read less
Was this helpful?
Thank you for voting!
broken terminal
3 of 3 people
found this instruction helpful.
-
Gary from Shirley, IN
- Really Easy
- Less than 15 mins
Simply removed the old heating element and plug the new element terminals into socket.
Was this helpful?
Thank you for voting!
Old coil broke.
6 of 12 people
found this instruction helpful.
-
Paula Collins from Needham, MA
- Really Easy
- Less than 15 mins
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people
found this instruction helpful.
-
Dave from SANTA BARBARA, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched
... Read more
off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Read less
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people
found this instruction helpful.
-
Daniel from Prescott, MI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa
... Read more
y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Read less
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people
found this instruction helpful.
-
sherri from elk horn, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p
... Read more
lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Read less
Was this helpful?
Thank you for voting!
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
3 of 4 people
found this instruction helpful.
-
judy from palatine, IL
- Really Easy
- 15 - 30 mins
just plugged it in!
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people
found this instruction helpful.
-
George from Irving, TX
- Really Easy
- Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Other Parts Used:
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!