38HN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip pans needed to be replaced
1 of 2 people
found this instruction helpful.
-
Mark from ROSENBERG, TX
- Very Easy
- Less than 15 mins
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Other Parts Used:
Was this helpful?
Thank you for voting!
The three braces under the coils had weakened and fallen apart
2 of 5 people
found this instruction helpful.
-
Suzanne from COZAD, NE
- Very Easy
- Less than 15 mins
I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.
Was this helpful?
Thank you for voting!
My drip pans were in bad shape
2 of 5 people
found this instruction helpful.
-
Sandra from Oldsmar, FL
- Really Easy
- Less than 15 mins
I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed
Other Parts Used:
Was this helpful?
Thank you for voting!
Terminal block arc'ed because a wire had become loose.
1 of 2 people
found this instruction helpful.
-
Larry from Scranton, KS
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All ch
... Read more
ecked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Read less
Was this helpful?
Thank you for voting!
cleaner
2 of 5 people
found this instruction helpful.
-
Mary from Duarte, CA
- Really Easy
- Less than 15 mins
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this helpful?
Thank you for voting!
missing clock knob
1 of 3 people
found this instruction helpful.
-
Jimmie from Hampton, VA
- Really Easy
- Less than 15 mins
placed knob on clock shaft with my fingers
Was this helpful?
Thank you for voting!
surface burner heating element broken
2 of 6 people
found this instruction helpful.
-
Marlene from Charleston, SC
- Really Easy
- Less than 15 mins
took out old element, replaced with new.
Was this helpful?
Thank you for voting!
element shorted out startedto arch inside oven
1 of 3 people
found this instruction helpful.
-
David from Traverse city, MI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.
Was this helpful?
Thank you for voting!
element or temperature sensor failed: not working
1 of 3 people
found this instruction helpful.
-
David from Mary Esther, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
Little or no heat from oven, cakes baking unevenly
3 of 10 people
found this instruction helpful.
-
STEVE from Lehigh Acres, FL
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced both parts to not take any chances. Had to first find the hole in the back of the oven for the temperature sensor kit. We were trying too hard and overlooked the obvious. It goes behind the small black panel, as you look at the back of the stove it is top left and held in place by only one screw. Once we found it everything went
... Read more
very well and the oven is working great-back in the cake business again!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven temperature lagging set temperature by almost 100F
0 of 1 people
found this instruction helpful.
-
William from Edgewood, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fi ... Read more xed the problem, so I just ordered the more expensive control board -- hope that does it.
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order
Unfortunately, neither the new bake element or sensor fi ... Read more xed the problem, so I just ordered the more expensive control board -- hope that does it.
Read less
Was this helpful?
Thank you for voting!
Bad broil grill
0 of 1 people
found this instruction helpful.
-
Aurelio from Lebanon, NJ
- A Bit Difficult
- More than 2 hours
-
Screw drivers
Once oven was removed from wall not to bad
Was this helpful?
Thank you for voting!
Had to replace heating element and element gasket
0 of 1 people
found this instruction helpful.
-
George from Camp Springs, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed old element and element gasket. Replaced both by alining gasket with element and screwing in retaining screws. Jod completed.
Was this helpful?
Thank you for voting!
Getting codes and beeping
1 of 4 people
found this instruction helpful.
-
Arthur from Dallas, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.
Was this helpful?
Thank you for voting!