EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38HN Magic Chef Range - Instructions

All Instructions for the 38HN
31 - 45 of 258

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Front left burner quit after bright flash under glass top
11 of 19 people found this instruction helpful.
  • Brian L. from Wilkes-Barre, PA
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the origina l unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect
Was this helpful?
Thank you for voting!
Door Spring Broke
7 of 9 people found this instruction helpful.
  • Thomas from Van Nuys, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Was this helpful?
Thank you for voting!
my oven would not heat to proper temp
6 of 6 people found this instruction helpful.
  • mark from CHAMBERLAIN, SD
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. T his repair took about 10 mins and the oven works perfectly. Thanks !
Was this helpful?
Thank you for voting!
Stove top wouldn't come on. Oven couldn't go higher than low heat
7 of 9 people found this instruction helpful.
  • Peter from FREDERICK, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland
Was this helpful?
Thank you for voting!
electric coils would not stay flat as drip pans were incorrect fit
6 of 7 people found this instruction helpful.
  • Janet from Philadelphia, PA
  • Really Easy
  • Less than 15 mins
replaced drip pans with correct type
Was this helpful?
Thank you for voting!
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
5 of 5 people found this instruction helpful.
  • Aubrey from EADS, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Was this helpful?
Thank you for voting!
the left front burner burned out & none of the lights to show if a burner was hot would come on.
5 of 5 people found this instruction helpful.
  • Richard from Fair oaks Ranch, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the count er.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.
Was this helpful?
Thank you for voting!
replace light in oven
5 of 5 people found this instruction helpful.
  • william from aiken, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people found this instruction helpful.
  • Sharon from Yacolt, WA
  • Really Easy
  • Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people found this instruction helpful.
  • Paul from Foley, AL
  • Really Easy
  • Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Was this helpful?
Thank you for voting!
The 6" heating element stop working on the stove top.
4 of 4 people found this instruction helpful.
  • JULIUS from JACKSON, MI
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brack ets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people found this instruction helpful.
  • Barbara a from Huntington, NY
  • Really Easy
  • Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
Left front burner went out.
5 of 7 people found this instruction helpful.
  • Donald from North Highlands, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people found this instruction helpful.
  • Rachael from Adams, MA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Was this helpful?
Thank you for voting!
All Instructions for the 38HN
31 - 45 of 258