38FB Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The heating element socket had crumbled with age.
4 of 4 people
found this instruction helpful.
-
Edward from Webster, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.
Was this helpful?
Thank you for voting!
Oven would not maintain temperature
5 of 7 people
found this instruction helpful.
-
KATHY from PLEASANT GAP, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is l
... Read more
ike new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
Read less
Was this helpful?
Thank you for voting!
The drip bowls were all caked and corroded.
4 of 5 people
found this instruction helpful.
-
Terry from Mountain City, TN
- Really Easy
- Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Other Parts Used:
Was this helpful?
Thank you for voting!
Panel light burnt out after 10 years
4 of 5 people
found this instruction helpful.
-
Pamela from La Junta, CO
- Really Easy
- Less than 15 mins
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just
... Read more
4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Read less
Was this helpful?
Thank you for voting!
Burner no longer worked.
4 of 5 people
found this instruction helpful.
-
Marcus from Emmett, KS
- Easy
- Less than 15 mins
-
Screw drivers
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this helpful?
Thank you for voting!
Just unscred the 2 screw on the Thermometer
4 of 5 people
found this instruction helpful.
-
WILLIAM J from JERSEY CITY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people
found this instruction helpful.
-
Trace from Ofallon, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces
... Read more
of sheet metal back on and plugged in the oven.
Read less
Was this helpful?
Thank you for voting!
oven would not come to set heat
4 of 5 people
found this instruction helpful.
-
Ralph from Portsmouth, NH
- Really Easy
- Less than 15 mins
-
Screw drivers
slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.
Was this helpful?
Thank you for voting!
broken terminal
3 of 3 people
found this instruction helpful.
-
Gary from Shirley, IN
- Really Easy
- Less than 15 mins
Simply removed the old heating element and plug the new element terminals into socket.
Was this helpful?
Thank you for voting!
Old coil broke.
6 of 12 people
found this instruction helpful.
-
Paula Collins from Needham, MA
- Really Easy
- Less than 15 mins
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this helpful?
Thank you for voting!
Crazy codes and not heating the oven properly at desired temp settings
3 of 3 people
found this instruction helpful.
-
Stan from CHICAGO RIDGE, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. I
... Read more
f you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Read less
Was this helpful?
Thank you for voting!
Uneven Heating/ High Heat Broiler To No Heat
3 of 3 people
found this instruction helpful.
-
Jack from Houston, TX
- Difficult
- More than 2 hours
-
Screw drivers
After replacing heating element then selector switch, I came to think the only other thing was the thermostat. It finally worked. . . But not without some tribulations. This note is for a repair involving thermostat for a w130 jenn-air or maytag wall oven, do not follow instructions included with replacement part! It says the br and ba
... Read more
terminals are to be reversed with this replacement part. . . Not so! After re-connecting (as per instructions) nothing worked! If you have this model jennair or maytag, my suggestion is to replace the wires to connections just as they were removed from the old one. I finally did this after much frustration and electrical testing with a multimeter. Hope this note helps someone. Good luck!
Read less
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people
found this instruction helpful.
-
Daniel from Prescott, MI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa
... Read more
y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Read less
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people
found this instruction helpful.
-
Dave from SANTA BARBARA, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched
... Read more
off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Read less
Was this helpful?
Thank you for voting!
Temp out of wack
3 of 4 people
found this instruction helpful.
-
Peter from Montello, WI
- Really Easy
- More than 2 hours
-
Nutdriver
replaced heat sensor
Was this helpful?
Thank you for voting!