EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3890 - Instructions

All Instructions for the 3890
91 - 105 of 113

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
ugly old drip pans.
  • Cindy from Champaign, IL
  • Really Easy
  • Less than 15 mins
It was simple! The range looks so much better!
Was this helpful?
Thank you for voting!
Needed to replace the burner knobs on my stove.
  • Candace from Iowa Falls, IA
  • Really Easy
  • Less than 15 mins
Great company....Fast delivery.
Was this helpful?
Thank you for voting!
needed drip pans for burner
  • Arva from Horsecape, KY
  • Really Easy
  • Less than 15 mins
easy, drop in
Was this helpful?
Thank you for voting!
The original filter was decomposing each time I washed it
  • Sharon from Kenai, AK
  • Really Easy
  • Less than 15 mins
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.
Was this helpful?
Thank you for voting!
Holes in the air filter of our Jenn-Air grill
  • Janice from Ocala, FL
  • Really Easy
  • Less than 15 mins
Simply pulled the old filter out and put the new filter in.
Was this helpful?
Thank you for voting!
Grease Filter no longer filtered
  • Phyllis from Stamford, CT
  • Really Easy
  • Less than 15 mins
Inserted filter in well. removed old know and replaced.
Was this helpful?
Thank you for voting!
Replacement
  • Barb from Holladay, UT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this helpful?
Thank you for voting!
Filter worn out, exhasut fan kept going off
  • John from Cayce, SC
  • Really Easy
  • Less than 15 mins
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete
Was this helpful?
Thank you for voting!
Burner knobs were old and some settings had worn off.
  • Athena from Mill Valley, CA
  • Really Easy
  • Less than 15 mins
Wrap first three fingers of right around old knob. Pull it off and throw in trash. Take new burner knob and slide it onto the stem. Repeat 3X, that is, once for each remaining burner knob. Time to complete job - 45 seconds. :-D
Was this helpful?
Thank you for voting!
Part was corroded
  • Ronald W from Colorado Springs, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took out the screws replaced the cartridge top, replaced the screws
Was this helpful?
Thank you for voting!
bearing went out in blower motor
  • richard from white castle, LA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Was this helpful?
Thank you for voting!
Two of the screw holes in the new tops do not line up with the holes in the existing pans.
  • HONESTO from HEMET, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
I had to remove the clip attached to the edge of the pan holding the wires so I can push the top down more for the holes to line up. The thickness of the clip prevented the holes to line up.
Was this helpful?
Thank you for voting!
Although the knobs where the correct ones, they did not fit over the stems correctly.
  • Alexander from Melrose, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I used the blow torch to heat up a small screwdriver till it was red hot. I then quickly applied it to the inside of the new knobs to make the shape more accommodating to the stems size. Once I thought I had about the right size, I heated the screwdriver again and melted the inside of the knob again and quickly pressed the know on to the stem and molded the inside as best I could to the stem.So far so good. Everything is working again.
Was this helpful?
Thank you for voting!
All Instructions for the 3890
91 - 105 of 113