3882 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip Pans were stained and burned on.
1 person
found this instruction helpful.
-
Sandra Collignon from SANTA CLAUS, IN
- Really Easy
- 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
original fixture required bulb - this fixture (all-in-one) was great
1 person
found this instruction helpful.
-
wesley from ODENVILLE, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pulled range out from cabinet-wall to get to back side, everthing was clearly exposed tlhen. Just a matter of installing new fixture, putting back on, reconnected power source - put range back in proper place.
Was this helpful?
Thank you for voting!
Replace the lower oven element
1 person
found this instruction helpful.
-
Tom from ROCKTON, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplug the 220 cord..remove rear metal back ( 7-8 Ph/screws)... disconnect the red & yellow connectors from the back of the lower element. Remove-the-lift-off Oven door. Remove the two Ph/screws (one on either end of the element) At the very rear of the oven. Install the new element and reverse the about to reassemble.
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person
found this instruction helpful.
-
Larry from SOLON, IA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Jennair cooktop with coils lost one of its coil guides.
1 person
found this instruction helpful.
-
Bruce from SOUTHBURY, CT
- Really Easy
- 30 - 60 mins
-
Socket set
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this helpful?
Thank you for voting!
Oven baking coil had burned out
1 person
found this instruction helpful.
-
Marie from Fredericksburg, VA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.
Was this helpful?
Thank you for voting!
The bake element burst.
1 person
found this instruction helpful.
-
Diane from Littleton, CO
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws that held the element in place and then pulled off the element from the connectors. Slipped the new connectors on. Tested the oven - Baked some blackberry cobbler!
Was this helpful?
Thank you for voting!
F5 fault code kept appearing
1 person
found this instruction helpful.
-
Louis Rodriguez from Granbury, TX
- Very Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed
... Read more
it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Read less
Was this helpful?
Thank you for voting!
Replaced upper over light and assembly
1 person
found this instruction helpful.
-
Thomas from SAN DIEGO, CA
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
I had to pull out the oven and balance the oven on two patio tables. Remove the back of the oven. Pull out the light assembly which was burnt. I was unable to remove the casing around the light, so I destroyed it with a pliers. Reinstalling the new light and assembly was easy. What made this job difficult, I could not remove the light ass
... Read more
embly from the front of the oven and had to go in from the back.
Read less
Was this helpful?
Thank you for voting!
Inner most oven door was broken.
1 person
found this instruction helpful.
-
William from WASHINGTON, DC
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
I followed peoples instructions here, and it was not very difficult.
Was this helpful?
Thank you for voting!
Oven door hinges broken
4 of 10 people
found this instruction helpful.
-
Brian from Lakewood, CO
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers
With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my
... Read more
own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
oven didn't heat up
1 person
found this instruction helpful.
-
robert from merrimack, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.
Was this helpful?
Thank you for voting!
No Bake, only Broil
1 person
found this instruction helpful.
-
Edward from Adamstown, MD
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
POWER OFF! Unplugged oven from wall.
(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)
Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed t ... Read more he new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)
Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed t ... Read more he new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.
Read less
Was this helpful?
Thank you for voting!
bake element disintegrated!
1 person
found this instruction helpful.
-
Susan from Grand Ledge, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
Seems every 5 years this bake element totally disintegrates, so we,re experienced! Pull the stove out and remove the back, remove the 2 screws that hold the element(now in 5 pieces), diconnect and discard. Place new element in and connect, replace the 2 screws holding the element in place. Replace stove back. Easy
Was this helpful?
Thank you for voting!
Lower element out-oven wouldn't heat
1 person
found this instruction helpful.
-
PATSY from HALLWOOD, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!
Was this helpful?
Thank you for voting!