3876 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Fan was getting really noisy.
1 person
found this instruction helpful.
-
frankie from Port Richey, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
Looked at fan and seen it was rubbing metal cage. After looking and checking fan noticed bushings were worn letting fan hit cage. Repair was very easy. Used a 1/4 inch nut driver to remove bracket holding fan. Pulled fan blade off shaft by just pulling it forward. Removed fan and replaced grommets. Reassembled fan and fan blade. Took
... Read more
just 10 minutes.
Read less
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person
found this instruction helpful.
-
Edward from E LONGMEADOW, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Read less
Was this helpful?
Thank you for voting!
Had a 'ticking' sound
1 person
found this instruction helpful.
-
John from PARKVILLE, MO
- Easy
- 30 - 60 mins
-
Socket set
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side o
... Read more
f the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Read less
Was this helpful?
Thank you for voting!
Noisy
1 person
found this instruction helpful.
-
Brad from SPRING MILLS, PA
- Very Difficult
- More than 2 hours
I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people
found this instruction helpful.
-
QUOC-LOC from LYNN HAVEN, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Read less
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people
found this instruction helpful.
-
Ted from SANDWICH, IL
- Easy
- 15 - 30 mins
-
Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people
found this instruction helpful.
-
Stephanie from KEARNY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
The door activated light switch was missing.
1 of 3 people
found this instruction helpful.
-
Don from Eugene, OR
- Really Easy
- Less than 15 mins
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this helpful?
Thank you for voting!
Bad switch for door prevented interior light from coming on
0 of 1 people
found this instruction helpful.
-
Patricia from Sylva, NC
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of yo
... Read more
ur company & it's repair video. THANK YOU SO MUCH
Read less
Was this helpful?
Thank you for voting!
Fan stopped working, Ice maker burned out
0 of 1 people
found this instruction helpful.
-
TODD from PLAINVILLE, CT
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Fan Quit So did the Ice Maker. $150.00 worth of parts plus my time. Also the Freezer Floor cracked for some stupid reason.
Other Parts Used:
Was this helpful?
Thank you for voting!
The evaporator fan in the freezer compartment began making a loud noise.
0 of 1 people
found this instruction helpful.
-
Boyd from Rapid City, SD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Cracked Dairy Door
0 of 3 people
found this instruction helpful.
-
Fr Kerry from Washington, DC
- Really Easy
- Less than 15 mins
PartSelect shipped me the part and it arrived in less than 3 days. It took longer to unwrap the excellent packing than it did to pop the new door into place. Wonderful!
Was this helpful?
Thank you for voting!