3865 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven Temperature was 50 degrees low
2 of 3 people
found this instruction helpful.
-
Eugene from Clinton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees
... Read more
low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Read less
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
The plastic parts that hold the brackett to the shelf were broken.
2 of 3 people
found this instruction helpful.
-
Sammy from Farmington, NM
- Really Easy
- Less than 15 mins
The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally.
Also the part came so quickly it was al ... Read more most as good as buying it here in town. Thanks. Donna Bingham
Also the part came so quickly it was al ... Read more most as good as buying it here in town. Thanks. Donna Bingham
Read less
Was this helpful?
Thank you for voting!
Bake element would no longer heat up
1 person
found this instruction helpful.
-
Joe from Schertz, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I unplug the stove first. Then took off two screws that held the bake element in place. Pulled off the connectors using the pliers. Had to use pliers because they were really snug. Plug in the wires to the new base element. Crimped down the connectors a little bit to make sure they were snug. Inserted the bake element back into the
... Read more
holes at the back of the oven. Put the two screws back in. Plugged the oven back in and turned it on to make sure it worked. Lastly, tossed the old bake element in the trash. Really easy job. Glad I didn't pay anybody to do this.
Read less
Was this helpful?
Thank you for voting!
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
1 person
found this instruction helpful.
-
Robert from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
Element burned out.
2 of 4 people
found this instruction helpful.
-
Raymond from Ottawa, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.
Was this helpful?
Thank you for voting!
bottom bake element broken and burned
1 person
found this instruction helpful.
-
Carolyn S from white oak, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.
Was this helpful?
Thank you for voting!
Bake element had burnt in half.
1 person
found this instruction helpful.
-
Joyce from ROCHESTER, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.
Was this helpful?
Thank you for voting!
Element burned out.
1 person
found this instruction helpful.
-
Wayne from Marietta, GA
- Easy
- Less than 15 mins
-
Screw drivers
Turn off breaker.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Unscrew old element, disconnect wires.
Connect wires to new element, tighten screws.
Breaker back to ON.
Done.
Was this helpful?
Thank you for voting!
snapped element
1 person
found this instruction helpful.
-
Paul from Yukon, OK
- Easy
- Less than 15 mins
-
Screw drivers
switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering
recieved my replacement part the next day after ordering
Was this helpful?
Thank you for voting!
Bake Element Melted
1 person
found this instruction helpful.
-
Bert from S. Easton, MA
- Easy
- Less than 15 mins
-
Screw drivers
Unplugged stove, unscrewed element pulled element out about 3 inces and disconnected element. Took model of stove looked on line for part. PartSelect had the best price and easiest web site to order part. Ordered part about 4pm and received part in 2 days. Took element out of box plug into connections and screwed the element back in.
... Read more
Plugged stove in and worked perfect.
Read less
Was this helpful?
Thank you for voting!
Bake Element shorted out
1 person
found this instruction helpful.
-
Laurie from Clarence, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I first shut off the breaker to the stove - safety first!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. ... Read more After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!
Read less
Was this helpful?
Thank you for voting!
Element burned in half
1 person
found this instruction helpful.
-
James from Allyn, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Was this helpful?
Thank you for voting!
My oven sparked, then wasn't working, so I turned to the internet.
1 person
found this instruction helpful.
-
Joan from Medford, OR
- Really Easy
- Less than 15 mins
-
Screw drivers
I received the new element on the third day, followed simple directions, and voila! I'm baking again.
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not ... Read more screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
First I unplugged the stove. Important!. Then with a phillips head screwdriver I removed the two screws at the back of the oven. The transition from busted to new was easy because there was a slide-in connection to the wires, not ... Read more screws. The best advice was sticking duct tape on the wires so they wouldn't go back into the inner sanctum before I was able to attach the new element. Hey, I'm a 72-year-old grandma, and it was easy!
Read less
Was this helpful?
Thank you for voting!