EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3865 - Instructions

All Instructions for the 3865
61 - 75 of 438

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Needed to replace the oven door gasket/seal
4 of 5 people found this instruction helpful.
  • Daniel from Katy, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people found this instruction helpful.
  • Trace from Ofallon, MO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.
Was this helpful?
Thank you for voting!
Broiler part wouldn't heat. Element internally broken
5 of 8 people found this instruction helpful.
  • Richard from Perkinsville, VT
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
i removed the two screws that holds the element in. I pulled the element out and disconnected the wires and I had to adapt a double male adapter to the wire ends and plug the wires back onto the element. The old element had male spades and the new element had female spades.
Was this helpful?
Thank you for voting!
Fridge doesn't cool properly; freezer iced up
4 of 5 people found this instruction helpful.
  • Will from Houston, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people found this instruction helpful.
  • Harlen from Spring Creek, NV
  • Really Easy
  • Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Was this helpful?
Thank you for voting!
Gasket was worn out.
3 of 3 people found this instruction helpful.
  • Michael from VALLEJO, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
Put a new one in.
Was this helpful?
Thank you for voting!
Broiler drawer front slide plastic guides broke so drawer sagged and was difficult to pull out.
3 of 3 people found this instruction helpful.
  • DOUGLAS from MESA, AZ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the single phillips screw that held each plastic slide guide to the stove, and replaced the part reusing the screws. Was so simple I didn't even have to swear. This was my mother-in-law's stove, and she was so happy to have it repaired she's fed me twice since.
Was this helpful?
Thank you for voting!
Old element caught fire, replaced with new one
3 of 3 people found this instruction helpful.
  • louis from CAHOKIA, IL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Removed screws of old element pulled clips off replaced with new element very easy
Was this helpful?
Thank you for voting!
door seal contaminated by a boil-over, not flexible
3 of 3 people found this instruction helpful.
  • Rob from Yakima, WA
  • Really Easy
  • Less than 15 mins
From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people found this instruction helpful.
  • Dave from SANTA BARBARA, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people found this instruction helpful.
  • Lee from OZARK, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people found this instruction helpful.
  • sherri from elk horn, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Was this helpful?
Thank you for voting!
was not defrosting
3 of 4 people found this instruction helpful.
  • denis from freedom, NH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom
Was this helpful?
Thank you for voting!
one electric burner does not get hot
5 of 10 people found this instruction helpful.
  • dinh from austin, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. U sed the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.
Was this helpful?
Thank you for voting!
end cap to bar of freezer door broke
3 of 4 people found this instruction helpful.
  • Kimberly A from Columbus, OH
  • Really Easy
  • Less than 15 mins
Snapped end cap onto bar and installed bar onto freezer door.

I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this helpful?
Thank you for voting!
All Instructions for the 3865
61 - 75 of 438