3862 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer stoped freezing
2 of 2 people
found this instruction helpful.
-
paul from ENDICOTT, NY
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE
... Read more
OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.
Read less
Was this helpful?
Thank you for voting!
Bake element eroded
2 of 2 people
found this instruction helpful.
-
Alison from NORTH EASTON, MA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Everything was straightforward other than the tabs that the screws go through before going into the back of the oven were the wrong size and the predrilled holes were not in the right location. Had to trim the metal tabs and redrill the screw holes.
Other Parts Used:
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people
found this instruction helpful.
-
phillip from Farmington, NM
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose
... Read more
by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Read less
Was this helpful?
Thank you for voting!
Broil element burst
2 of 2 people
found this instruction helpful.
-
Ronald from WEST COLUMBIA, SC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Drop in range was in excellent condition until element burst and was getting ready to purchase another range and then I was looking to replace the element and found part select and they were great from the order process and shipping was fast and the whole process was 5 STARS. As far as me doing the repair I watched the video and it was s
... Read more
imple for even me. I also replaced the bake element at the same time. Once again I highly recommend Part Select and they are second to none.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Not cooling and freezer freezing up
6 of 14 people
found this instruction helpful.
-
kenneth from carmel, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
Bake element caught on fire
2 of 2 people
found this instruction helpful.
-
Dan from TomRriver, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I got the run around about my HARWICK stove at several part stores. Like they all said the same thing (cant look it up just bring it down) So i did and then they would say, what's the model number. ERR! SO my wife found parts select on the web and they beat the three price quotes I got. First turn the power off to the stove!!! The repair
... Read more
was simple. Just remove the two screws on both side's and pull the element out but just enough for the wire's to show. Disconnect the two wire's and pull the element out. Reverse the processes but when wire's are reconnected squeeze terminals end gently to ensure a good connection. This is a great company to deal with, I will be using them again. Thanks and good luck!!!
Read less
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Baking element burned out
2 of 2 people
found this instruction helpful.
-
Stephen from Pleasant Hill, IA
- Easy
- Less than 15 mins
-
Screw drivers
I watched the video on the web site and it worked like a dream. Two screws to take out - disconnect wires put back connecting wires and replace the screws again. Just like the video. Thanks
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 2 people
found this instruction helpful.
-
francis from mount holley, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor.
... Read more
That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Read less
Was this helpful?
Thank you for voting!
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
2 of 2 people
found this instruction helpful.
-
richard from SAINT MARYS, KS
- Very Easy
- Less than 15 mins
-
Screw drivers
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this helpful?
Thank you for voting!
The element on my 20+ year old Jenn Zaire oven had broken in two...
2 of 2 people
found this instruction helpful.
-
Mary from New Britain, PA
- Very Easy
- Less than 15 mins
-
Screw drivers
Went online to find replacement part. (Because I’m cheap) Came across the website, found the part by model number, and watched the wonderful replacement video that was right on the same page as the part. After the part arrived, (in just a couple of days) I put the new one in. Only took a couple of minutes! Perfection! Thanks for making m
... Read more
y problem, no problem at all!
Read less
Was this helpful?
Thank you for voting!
left cover for the oven light broke when trying to replace the bulb
2 of 2 people
found this instruction helpful.
-
Mark from SHOREVIEW, MN
- Very Easy
- Less than 15 mins
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people
found this instruction helpful.
-
Lynn from BRADENTON, FL
- Really Easy
- Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Other Parts Used:
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people
found this instruction helpful.
-
Frances from Summerfield, FL
- Really Easy
- Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Other Parts Used:
Was this helpful?
Thank you for voting!