3859 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fridge light dead even with new bulb
1 person
found this instruction helpful.
-
marj from NEWBURY PARK, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
1 person
found this instruction helpful.
-
Robert from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people
found this instruction helpful.
-
ED from ENON, OH
- Very Easy
- Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
broken door shelf bar holder
1 of 2 people
found this instruction helpful.
-
Stan from Dallas, TX
- Really Easy
- Less than 15 mins
I ordered the part before noon and I they had it out the door and in my hands within 24 hours! It took about 2 minutes to take out the broken part and snap in the new one!Great service and easy install!
Was this helpful?
Thank you for voting!
The control board generated clicking noise. Temperature display wrong values.
1 of 2 people
found this instruction helpful.
-
QUOC-LOC from LYNN HAVEN, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
P ... Read more lugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Read less
Was this helpful?
Thank you for voting!
socket had melted
1 of 3 people
found this instruction helpful.
-
Chris from Charlotte, NC
- Really Easy
- Less than 15 mins
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this helpful?
Thank you for voting!
Light socket missing in refrigerator
1 of 4 people
found this instruction helpful.
-
Wayne from Issaquah, WA
- Really Easy
- Less than 15 mins
Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.
Was this helpful?
Thank you for voting!
This part broke for whatever reason, I do not know.
0 of 1 people
found this instruction helpful.
-
John D from Chevy Chase, MD
- Really Easy
- Less than 15 mins
-
Pliers
I needed a pliers to extract the shelf reatainer from its place in the door of the fridge.
I found the part in the partSelect catalog, ordered it, opened the box, and snapped the replacement part into place. I then popped the Shelf retainer back into place where it belonged.
Piece of cake.
I found the part in the partSelect catalog, ordered it, opened the box, and snapped the replacement part into place. I then popped the Shelf retainer back into place where it belonged.
Piece of cake.
Was this helpful?
Thank you for voting!
Broken door shelf retainer
0 of 1 people
found this instruction helpful.
-
Bill from Prescott, AZ
- Really Easy
- Less than 15 mins
Just replace end cap and install. The beauty of this was the door was broken in the evening before July 4 when all retail had closed down early for the 4th weekend. I hit Part Select on the computer, scrolled down the partslist,looked at pictures and figured out from that the necessary piece I needed, hit the buy button and in less than 1
... Read more
0 minutes had an order placed. July 7 UPS was at the door with the parts and my reefer was back in business. NO service call and no extra charges!!! Thank You, PartSelect!!!!
Read less
Was this helpful?
Thank you for voting!
door shelf cap was broken and shelf fell off the door
0 of 1 people
found this instruction helpful.
-
Lynn from Montvale, NJ
- Really Easy
- Less than 15 mins
-
Pliers
Removed the broken part with a pliers.
Inserted end cap into shelf, then into door.
PERFECT!!!
Thank you
Inserted end cap into shelf, then into door.
PERFECT!!!
Thank you
Was this helpful?
Thank you for voting!
The plastic bracket that holds the lower shelf in the refrigerator door broke
0 of 2 people
found this instruction helpful.
-
Alan from La Jolla, CA
- Really Easy
- Less than 15 mins
The bracket arrived promptly after ordering by telephone and snapped into place easily.
Was this helpful?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
12 of 46 people
found this instruction helpful.
-
Alberto from PALMETTO BAY, FL
- Really Easy
- 30 - 60 mins
-
Socket set
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Was this helpful?
Thank you for voting!
The bottom part of fidge was warm with water droplets on the its ceiling.
-
Charles R from Renton, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart b ... Read more rackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart b ... Read more rackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Read less
Was this helpful?
Thank you for voting!
Refrigerator and freezer drawer would not maintain set temperature
-
James from Bel Air, MD
- A Bit Difficult
- 30 - 60 mins
-
Socket set
Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I o
... Read more
rdered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.
Read less
Was this helpful?
Thank you for voting!