This is a replacement screw, also known as a shear pin that is used in several pieces of outdoor power equipment. It is made of metal and is approximately 2 inches in length. It is a hex head screw and is sold individually. This is an OEM part sourced directly from the manufacturer.
The fuel tank goes between the fuel tank bracket and the fuel line. This is a Tecumseh, Husqvarna, and Toro replacement part directly sourced from the manufacturer for use in engines and snowthrowers. This part holds the fuel and is priced individually. A wrench might be required during the replacement of this part. It will need to be replaced if it leaks.
This is an authentic OEM self-tapping bolt used on Toro snow throwers/blowers. It is designed to secure the bushing/gear case assembly together. By using a wrench and a self tapping bolt, precisely fitted threads are created in the opening of the case. This allows for the two part to be secured tightly together. Please note this bolt is sold individually.
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.
This snap ring fits into a groove to hold a pinion gear or other drive part in place. A loose drive part may mean the ring is bent, weak, or missing. Check the groove, washers, bearings, and shaft for damage before replacing it. Confirm fit with the full machine model, serial range, and parts diagram. Turn off the equipment and disconnect...Read more the battery or spark plug lead when needed. Wear eye protection and use retaining-ring pliers. Make sure the new ring sits fully and evenly in the groove before use.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers and a screwdriver. If broken due to wear/fatigue/damage, there may be a fuel leak and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This metal ball bearing reduces friction and evenly distributes weight among the rotating parts in your lawn equipment. These bearings can be found in various areas such as the wheels, in pulleys, blades or augers. When the bearing is damaged, you may notice a few things. Your machine may produce rough or grinding noises and excessively p...Read morelay or wobble. The affected part may also become stuck. Immediate replacement is necessary to prevent increased friction, inefficient performance, and potential equipment failure. Removing the bearing depends on your model, so consult your user manual for guidance. You will need to use a screwdriver or pliers to remove the surrounding components around the bearing and a bearing puller, pry bar, or mallet to release the bearing itself from its housing. As ball bearings wear out together, it is advisable to replace all of them at once. Ensure you verify the number of bearings your machine needs before purchasing this OEM replacement part as it is sold individually.
This is a genuine replacement part manufactured for use with outdoor power equipment. This flanged hex head screw has several applications, please see model diagram for part use and location. This screw is available as an individual replacement part.
This 1/4-20 x 3/4-inch hex-head screw secures parts on compatible outdoor power equipment. It is made from Grade 5 steel and has a yellow zinc finish for added rust resistance. Check the equipment model and parts diagram before ordering.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bad Camshaft made of plastic
5 of 9 peoplefound this instruction helpful.
Dan from Millstone Twp, NJ
Really Easy
30 - 60 mins
Ordered a replacement camshaft and had a terrible result. Supposed to be in stock but wasn't. NO update on when the part would arrive. NO contact unless I initiated it. Only email I received stated NO information on when part would arrive. I asked for Customer service to reach out for more details and they balked, did not want to do a
... Read morenything. I insisted and the result was an email stating no idea. No further info from anyone. I figured my next step was to ask for a refund but figured it would not be refunded. I then found a "dead" engine and used THAT camshaft for my repair. Weeks later your part arrived with ZERO notice. I should have asked for a refund due to your failure to live up to your hype. ZERO stars for this junk. Will NOT ever use you again.