The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.
This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move.
If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.
This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).
Length 8 Foot
Length: 6'
Gauge: 18
Wires: 2
Type: Bare Wire
This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately.
Replacing this power supply cord you will need a screwdriver.
• Remove the housing screws
• Remove the the housing
• Disconnect the old cord wires
• Remove the old power cord
• Secure the new cord in place
• Connect the wires
• Reassemble and test the new cord
This is a type of handle with a knob-shaped grip used in a variety of lawn and garden tools with adjustable features. This genuine OEM part is 0.8 x 0.2 x 1 inches and is made from plastic. It is designed to connect and disconnect individual parts together without using any tools. By loosening the knob, you can easily adjust the height of...Read more the handles on your equipment to your liking as well as fold the handles for proper storage. Over time the handle knob can wear down or break. If this happens, you will need to unscrew the knob and remove the old rope guide before you can place the new knob on. Place the new rope guide in position, thread the eye of the cable through the eye hook loop and finally thread the new knob on to the shaft and turn it clockwise with your hands until it is secure.
This Throttle Control Wire is a 55-inch black Throttle Cable, made of metal with a rubberized casing. It's rated as "Easy" to install, attaching from the throttle control to the carburetor, and requires both pliers and a screw driver. This cable controls the speed of the engine. If broken or damaged (due to typical wear from use) you will...Read more lose control of the engine speed, and the part must be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This is a genuine manufacturer-sourced component which is specially designed for lawn mowers. This is the box that the throttle cable is connected to. The cable connects to the carburetor and it stops the engine when you shift the lever to the full choke position. To ensure the correct repair procedure, refer to the appropriate diagrams f...Read moreor your model. Keep in mind this high-quality throttle box is sold as an individual item. It includes the housing, the trigger, and the hardware to secure these components. A screwdriver will be needed to perform this repair.
This authentic replacement blade is sourced directly from original equipment manufacturer for use with walk-behind lawn mowers. Mulching blades are designed to circulate the grass longer so it can be cut into smaller pieces. This makes your grass clippings better as mulch since the smaller clippings will decompose quicker, releasing their...Read more nutrients into the soil. This part is made from strong, durable metal and it is sold individually.
This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.
This operator presence cable is a genuine OEM replacement designed for walk-behind lawn mowers. It connects the handle bail to the engine brake system, ensuring the engine stops immediately when the handle is released for safe operation. Built for reliable performance with correct cable length and fittings, it’s an ideal replacement when ...Read morethe mower won’t shut off properly or the original cable is stretched, frayed, or broken.
This is an original replacement part manufactured for use with walk-behind lawnmowers. The metal rope guide mounts to the side rail of the handle, and is secured by a handle knob. The rope guide keeps the starter rope on the upper handle for ease of access, and to keep the rope out of the way while operating. The rope guide is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Rear flap had deteriorated.
3 of 4 peoplefound this instruction helpful.
David from PITTSBURGH, PA
A Bit Difficult
30 - 60 mins
Pliers
Grip each retaining clip next to the housing with large pliers. Squeeze clip completely and pull straight out. Important: Do not attempt to bend clip up or down as clip may bend and become very difficult to remove. When old flap is removed, mower edge can be cleaned and painted to avoid rust. Install new flap in same direction front/rear
... Read moreas removed flap. Reinstall clips in same direction as they were, as up and down sides are not the same.
Read less
Was this helpful?
Thank you for voting!
Old power cord frayed at the grommet entering the drill casing
4 of 13 peoplefound this instruction helpful.
Bruce from HILLSBORO, OR
Very Difficult
30 - 60 mins
Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198 Email sent (11/16/2023) to partselect.com has gone unanswered Thanks?