3659 Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker putting black pieces of plastic in the ice
2 of 2 people
found this instruction helpful.
-
Doug from Lewisville, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.
Was this helpful?
Thank you for voting!
Ice maker not working.
2 of 2 people
found this instruction helpful.
-
kurt from Westminster, CO
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a g
... Read more
uide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.
Read less
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
2 of 2 people
found this instruction helpful.
-
Lyle from Bismarck, ND
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I removed the screws on the back of the refrigerator revealing the water valve, disconnected the water supply, removed the two outlet hoses and removed the bad valve. Replaced in the opposite manner.
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people
found this instruction helpful.
-
Mark from Farmington Hills, MI
- Easy
- 15 - 30 mins
-
Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
None
2 of 2 people
found this instruction helpful.
-
Dennis from Strongsville, OH
- Really Easy
- Less than 15 mins
My wife just snapped it in.
Was this helpful?
Thank you for voting!
Bottom Cam broke on Fridge Door
2 of 2 people
found this instruction helpful.
-
Jon from Butler, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers, Socket set
Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.
Was this helpful?
Thank you for voting!
lights did not work
2 of 2 people
found this instruction helpful.
-
Daniel from rochester hils, MI
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
pulled out old socket and replaced supposed to be a duel socket but no longer exists
Was this helpful?
Thank you for voting!
Old ice maker started leaking
2 of 2 people
found this instruction helpful.
-
Curtis from Barrington, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.
Was this helpful?
Thank you for voting!
One side of the kick plate grill was broken (faling of fridge).
2 of 2 people
found this instruction helpful.
-
Meghan from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped off the grill via the one remaining clip. Used a flathead screwdriver to pop the old, broken clip off. Then popped the new clip on to the holder. Done!! Super easy. Wish I had done it 2 years ago when the thing first broke instead of trying to jury-rig it!
Was this helpful?
Thank you for voting!
door closure part broken. door wouldn't remained closed
2 of 2 people
found this instruction helpful.
-
Patricia from JACKSON, WY
- Really Easy
- Less than 15 mins
-
Socket set
removed door.examined problem,. installed part. super easy
Was this helpful?
Thank you for voting!
Not making ice, and water leaking in freezer
2 of 2 people
found this instruction helpful.
-
Raymond from Northglenn, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness
Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on
ALL FIXED!
Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on
ALL FIXED!
Was this helpful?
Thank you for voting!
Old ice bucket had cracked around the auger.
3 of 5 people
found this instruction helpful.
-
KENNETH from COLLIERVILLE, TN
- Really Easy
- Less than 15 mins
-
Nutdriver
Transferred old auger and faceplate to new ice bucket. Auger was retained by left-handed nut. Faceplate was retained by 1/4" self-tapping screws.
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people
found this instruction helpful.
-
Karl from Wellesley, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Black flecks in the ice
2 of 2 people
found this instruction helpful.
-
Jon from Leander, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.
... Read more
The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)
After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.
The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)
After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.
Read less
Was this helpful?
Thank you for voting!