EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3658 Refrigerator - Instructions

All Instructions for the 3658
121 - 135 of 638

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Black flecks in the ice
2 of 2 people found this instruction helpful.
  • Jon from Leander, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I made use of instructions for other users, see 'My ice maker has been shedding.....' and they were very helpful. The one problem not covered - the instructions that came with the new icemaker said to 'remove the bearing and inlet from the old icemaker and install in the new icemaker', but gave no instructions for how to accomplish this.

The old inlet has a square opening in the back and a u-shaped knockout in the side. The new one has a round opening in the side and square knockout in the back)

After several attempts to remove them, I gave up and used the new inlet with the knockout removed. I did not attempt to cover the side opening and it worked fine that way - no leaks.
Was this helpful?
Thank you for voting!
I went by the video but my removal and installation were different than shown.
2 of 2 people found this instruction helpful.
  • Gregory from GARNER, KY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be rem oved and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.
Was this helpful?
Thank you for voting!
Old ice maker stopped working
2 of 2 people found this instruction helpful.
  • Sara from Nashville, TN
  • Easy
  • 15 - 30 mins
  • Nutdriver
Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.

Thanks...Ron Norwood
Was this helpful?
Thank you for voting!
Ice maker flaked and leaked leaving big glob of ice
2 of 2 people found this instruction helpful.
  • chris from manvel, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to r einstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.
Was this helpful?
Thank you for voting!
Defroster heater coil broken
2 of 2 people found this instruction helpful.
  • Anders from Eagan, MN
  • Easy
  • 15 - 30 mins
  • Socket set
Removed covers. Lifted and angled out the freezer unit. Removed clips at bottom and pulled out the heater coil. Threaded the new coil in place and replaced the clips. Lifted and hung freezer unit back in place. Re-connected wires and turned on the fridge. Verified that fan worked when cooled down and defrosted at end of cycle. Replaced th e covers.
Was this helpful?
Thank you for voting!
non-stick coating detioration and water overflow becoming large ice chunks
2 of 2 people found this instruction helpful.
  • Jeffrey from Murphy, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Ice maker assembly required disconnection of the wire harness at the back of the freezer and the removal of 3 hex nuts. The assembly did not come with a new wire harness nor the rigid wire attached to the hinge that can be raised to stop production of ice. The wire harness was easy to disconnect from the old assembly by pressing in on a tab. The rigid wire attached to the hinge simply required pulling straight out of the hinge-hole (no need to twist, slide, or perform other contortions...it does require significant force to remove, but it does pull straight out). It was simple to attach it to the new ice assembly. Reinstalled the 3 hex nuts and wire harness plug and was good to go....after waiting several hours! I was worried at first because the unit did not immediately fill with water after I plugged the fridge back into the wall socket. However, after the freezer was cold enough, the water did run and I had my first ice dump within about 3 hours of finishing the installation. We have good ice again, and Partselect has excellent pricing and awesome delivery! I received the unit the day after ordering, and I had only paid the basic shipping! Thanks Partselect! Jeff
Was this helpful?
Thank you for voting!
Heater was stuck on
3 of 5 people found this instruction helpful.
  • Jon from Helena, MT
  • Easy
  • 15 - 30 mins
  • Nutdriver
Replaced ice maker but now water valve wont work
Was this helpful?
Thank you for voting!
water into bin (big frozen chunks)
2 of 2 people found this instruction helpful.
  • Roger from Mesa, AZ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rota ting blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.
Was this helpful?
Thank you for voting!
The ice maker was leaking
2 of 2 people found this instruction helpful.
  • Jay from Richardson, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the h arness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker
Was this helpful?
Thank you for voting!
water leaking into ice tray, frozen glob of ice
2 of 2 people found this instruction helpful.
  • james from newfield, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers
installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.
Was this helpful?
Thank you for voting!
Icemaker made some pretty sad cubes! Hollow, unfilled, or small cubes
2 of 2 people found this instruction helpful.
  • Dana from ABINGTON, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.
Was this helpful?
Thank you for voting!
The water and ice on the door were not producing water or ice
2 of 3 people found this instruction helpful.
  • Erik from Lake Forest, CA
  • Easy
  • 15 - 30 mins
  • Socket set, Wrench (Adjustable)
1. Moved the firdge out so I had room to get bhind it.
2. Un-plugged the fridge so I didn't get electrocuted.
3. disconnected the the water hose from the broken water inlet with adjustable wrench.
4. Put hose in bucket to drain and moped up water from inlet valve with towel.
5. removed the 2 scrwes with socket driver t hat holds inlet on fridge.
6. reached in behind the inlet valve and unplugged the wires from the inlet valve (total of 2 plugs)
7. pulled the inlet valve out of the back of the fridge.
8. removed the bolt that holds the ground wire the metal plate that the inlet valve was connected to.
9. removed the defective inlet valve from the metl plate and tossed the defect valves.
10. put the metal plate on the new inlet valve.
11. screwed on the ground wire to the metal plate from new valve.
12. plugged in the 2 plugs back onto there proper locations on the inlet valve.
13. put the assembly back into place in the back of the fridge and screwed in the remaining 2 screws to hold it in place.
14. Put plumbers tape around outside of inlet to reduce leaks.
15. re-attached the hose and tightened it with the wrench.
16. turned on the water from the wall and verified there were no leaks.
17. Plugged in the fridge and tested that the water on the door worked.
18. Pushed the fridge back into place and the kids could once again enjoy water from the door of the fridge and in about 5 hours we had some ice again for our drinks.
Was this helpful?
Thank you for voting!
noisy fridge, perimeter of door heating up
2 of 3 people found this instruction helpful.
  • craig from maple grove, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.
Was this helpful?
Thank you for voting!
icemaker quit working
2 of 3 people found this instruction helpful.
  • craig from green bay, WI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.
Was this helpful?
Thank you for voting!
Ice Maker Leaked Creating an Ice block
2 of 3 people found this instruction helpful.
  • Loren from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this helpful?
Thank you for voting!
All Instructions for the 3658
121 - 135 of 638