3657 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice cubes in bin frozen into big lumps due to water leaking into bin from icemaker. Lining of icemaker cube tray worn and damaged allowing leak.
3 of 4 people
found this instruction helpful.
-
Ross from Sun Lakes, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Pull refrigerator out from wall to shut off water and power. Remove ice bin, pulling front down then out. Remove screw at bottom of icemaker, then pull down to release two clips, Pull out a couple inches to get hand behind icemaker to release wiring harness connector. (squeeze top and bottom to release clips). Remove unit. Remove wiring
... Read more
harness and wire bail from old unit and install on new unit. Reverse steps to install new unit. Make sure ice bin is fully inserted, or unit will not function.
Read less
Was this helpful?
Thank you for voting!
Melted ice bucket in dishwasher
3 of 4 people
found this instruction helpful.
-
Mary Kay from Cincinnati, OH
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed a few screws from front of old ice bucket and removed the inside part of the ice bucket. Forced the inside coil thing back into the new ice bucket and then attached the front back on to the new bucket also. The hardest part was manuvering the coil part out and back in - but in general it was a very easy fix.
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
Ice maker stopped working
3 of 4 people
found this instruction helpful.
-
Raymond from Panama City Beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
After checking the water valves ordered new ice maker. received the part three days after ordering! Clearing out food, removing the old one and installing the new unit took under 15 minutes. Everything went fine.
Was this helpful?
Thank you for voting!
The refrigerator stopped running
4 of 7 people
found this instruction helpful.
-
Barbara H. from South Hill, VA
- Easy
- 1- 2 hours
-
Screw drivers
I was told to order the run capacitor and the technician thought it would repair the refrigerator; but it did not. The appliance technician had to take the run capacitor off and install what he called a "hard start" and the refrigerator is operating right now.
Was this helpful?
Thank you for voting!
Ice maker stopped functioning
3 of 4 people
found this instruction helpful.
-
richard from colorado springs, CO
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.
Was this helpful?
Thank you for voting!
The door made a loud noise on opening and closing.
3 of 4 people
found this instruction helpful.
-
Dennis from Kerrville, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Emptied the door.
Removed the door, top bolts first.
Lifted out the door.
Installed new cam at the bottom.
Set the door back in place.
Bolted the top hinge back on.
Smooth!
The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.
Removed the door, top bolts first.
Lifted out the door.
Installed new cam at the bottom.
Set the door back in place.
Bolted the top hinge back on.
Smooth!
The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.
Was this helpful?
Thank you for voting!
dual light socket in fridge shorted out
4 of 7 people
found this instruction helpful.
-
Kimberly from Blue Springs, MO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
took old socket out, ordered replacement part, dual socket no longer available. Turn off power to appliance, attach new single light socket, screw light socket and light socket holder back into place. Turned on power and it worked. No instructions included in packet, attached wrong first time, blew fuse, attached socket a different way
... Read more
, and it worked.
Read less
Was this helpful?
Thank you for voting!
leaky ice maker - non-stick coating had failed
4 of 7 people
found this instruction helpful.
-
Robert from Sunnyvale, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
replaced the entire ice make - 3 screws and a squeeze -off connector and it's out. Reverse to re-install... except that the fill tube had iced up. To thaw the fill tube: unload freezer section (leave food in fridge, but keep door closed), remove ice maker. Boil water, dip drill bit (dull end) into hot water, swirl around, insert (dull en
... Read more
d) into to fill tube. Depending on how hot you got it, maybe a tablespoon of ice will melt. Repeat many times - fill tube is about 14" long! Do not use anything sharp - you will nick the tube and ice will form causing you to repeat this procedure. Do not try to break the ice - let the heat work. It took me about 30 minutes to thaw the whole thing - it made a nive gasping noise when the final plug opened up. Re-install ice maker.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Old ice maker started leaking
2 of 2 people
found this instruction helpful.
-
Curtis from Barrington, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.
Was this helpful?
Thank you for voting!
Ice maker not getting water (1 of 2 step troubleshooting)
2 of 2 people
found this instruction helpful.
-
Steven from Cisco, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Wrench (Adjustable)
Removed water inlet solenoids screws on base and pulled it out about 6 inches; removed 4 tubing nuts. Replaced unit with new and replaced tubing and base. This did not solve the problem so I ordered ice maker unit. Should of checked the inside of the ice maker ias the protective coating was pretty much history so I would ordered it first,
... Read more
and then ordered the inlet valve.
Read less
Was this helpful?
Thank you for voting!
One side of the kick plate grill was broken (faling of fridge).
2 of 2 people
found this instruction helpful.
-
Meghan from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped off the grill via the one remaining clip. Used a flathead screwdriver to pop the old, broken clip off. Then popped the new clip on to the holder. Done!! Super easy. Wish I had done it 2 years ago when the thing first broke instead of trying to jury-rig it!
Was this helpful?
Thank you for voting!
water overflow,coating on tray peeling off
2 of 2 people
found this instruction helpful.
-
Jeffery from vero beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
remove 3 screws,rotate assembly,depress lock on wire harnass connector,un plug harnass.remove old assembly,remove and transfer side cover and steel wire at front of assembly,connect harnass to new assembly,rotate into place,aling screw holes and install 3 screws.flip front steel wire down and wait for about 1 hour,first tray of ice will
... Read more
fall..all done.
Read less
Was this helpful?
Thank you for voting!
water leak and frezes ice in bin
2 of 2 people
found this instruction helpful.
-
Peter from Lancaster, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
to easy to describe, remove 3 screws and a wire plug then install new unite.
Works great
Thanks
Works great
Thanks
Was this helpful?
Thank you for voting!
lights did not work
2 of 2 people
found this instruction helpful.
-
Daniel from rochester hils, MI
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
pulled out old socket and replaced supposed to be a duel socket but no longer exists
Was this helpful?
Thank you for voting!