3654 - Instructions

I didn't know what the problem was so replaced all 3 parts.
What I think actually fixed the problem is the Cold Control Thermostat that is not listed here. This part accessed by removing the dial control in the front of the Freezer. Part wasn't exactly the same but worked. I looped the sensor toward the front of the dial. Also ... Read more replaced the Run Capacitor from the the back of the unit (Very Easy). Replaced the Defrost Timer from the Front of the unit (Easy). Now keeping 35-40 degrees in the Fridge and -15-0 in the Freezer. Nice. I plan to replace the Condenser Fan Motor also as it is a bit noisy.

Took the rear bottom panel loose , the ice maker and water dipenser valve is in the right corner. Turn off water line to the refrigerator , and also unplug the electric from the outlet. It is easier to take the ground wire loose from the valve bracket now , before taking valve out of the bracket. take the two water lines that run to the d ... Read more oor and the ice maker loose, then remove the main inlet line. Once you have the water lines off, then you can remove both electrical plugs from the electric coils. The water lines that run to the door and the ice maker cant be confused , because they are two different sizes , so they will only fit the correct side. The electrical plugs are pretty simple as well as, the wires are the same color as the coils, so its fairly easy to see which one goes where. The replacement process is pretty self-explanitary , just reverse the order. Just as a hint of advice , have a sponge or mop ready to clean up the water that comes out of the lines when you remove them. I also changed the drum wheel in the front of the ice bin, this process is not easy if you let the blades and spacers fall apart , as they have to pretty much have to be in correct order , or your ice bin will not crush ice , and you could possibly bust the bin into pieces. The process is not really hard , just pay close attention to what is coming off from where!!! There are two bolt on the bottom of the front cover , take them loose and pull the cover forward from the bottom, then lift a little , should come off. Then the metal front cover should be exposed, ther are two bolts in it as well , remove them , and the front should be loose , this is when you hold the auger and keep an eye on the blades. There is also a nut , right in the center of the wheel you have to take loose , hold the auger then take the nut loose with a 1/2 in. wrench. Once you remove the nut the drum pulls right off the auger. When going back together , make sure the ice crusher blades all line up correctly , as the blades wont work at all . They have to slide back into the blade pivot bracket (slot made into the plastic bucket front). As I said before , be sure and pay close attention , and this process will go easily. The drum is marked front side , or this side out, be sure its installed correctly , as the ice will not feed right. The first cycle of the ice maker making ice will probably be only 1 or 2 cubes , but the second time around you will have a full set of 8 , the water lines get air in them while they are unhooked so you wont get a full cycle the first time.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there w ... Read more aiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

change light bulbs

Did not know that kick grill did not include attachment pins. Removed old pins from broken grill and experienced very difficult time re-applying them to new grill.

I didn't. Don't know how to get to light bulb to change it for this specific model

We came home from a long vacation to discover a warm refrigerator with its contents in various stages of decay.

Turning the freezer thermostat to its warmest setting then back to cold generated clicks, and after a few tries the compressor started and cooled the refrigerator to its normal cold temperatures. But… later the co ... Read more mpressor again failed to start, and everything warmed back up again. With persistence and turning the thermostat up and down several times a day, we could keep the fridge cold.

It was time to order parts. We needed a new start relay and capacitor for the compressor. For our Amana ARB2214CW a start relay (WP12555902) and capacitor (WP65889-4) were listed on the first page of the Partselect parts list for my refrigerator. I ordered them, received them, removed the old capacitor and start relay (which rattled when shaken). and prepared to install my new parts. The new start relay did not match the old. The old start relay fit my wiring which had a single plug with two small female spade connectors in the plug. The new start relay required wiring with two separate female spade connectors; one the normal size and one larger. Phone calls to Partselect and to Westinghouse shed no light on the discrepancy. On the second page of the Partselect parts list was a combination of a start relay and a capacitor (W10613606) that matched my electrical connector. I could see the connection in the photograph. I ordered it and it fit. Easy peazy. That fixed the compressor start problem. Every time the freezer thermostat clicked on, the compressor started. Success.

But… from our troubleshooting we now had a thermometer the freezer, and it was obvious that the temperature difference between the cold point where the thermostat turned the compressor off and the warm point where the thermostat restarted the compressor was much too wide. In addition, the knob was hard to turn and was sticky as it turned. Oiling it fixed the sticky knob problem but not the wide temperature difference problem. I ordered a new freezer thermostat (WP67003000), received it, installed it, and all is now fine with my refrigerator. The new thermostat was physically a little different from the original, but it fit and worked.

I returned the first compressor start relay and capacitor and received a refund including the shipping charge.

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning ... Read more on the water supply and bingo...lots of ice cubes.

I ordered a new relay and capacitor installed them and it went right to work.
I paid for fast delivery and received parts the next day!

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Loosened all retaining screws around gasket - removed old gasket - inserted new gasket and tightened screws. Little tedious (lots of screws) but very simple.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.