EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3653 - Instructions

All Instructions for the 3653
106 - 120 of 778

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fridge doesn't cool properly; freezer iced up
4 of 5 people found this instruction helpful.
  • Will from Houston, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver
You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.
Was this helpful?
Thank you for voting!
Broken wheel
4 of 5 people found this instruction helpful.
  • Eric from Woods Cross, UT
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.
Was this helpful?
Thank you for voting!
Water overflowing ice maker
5 of 8 people found this instruction helpful.
  • James from Denver, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.
Was this helpful?
Thank you for voting!
Ice maker quit making ice. I believe the motor was tired after 20 years.
4 of 5 people found this instruction helpful.
  • James from Brighton, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
First I removed the ice catcher bucket to give myself a little room and lifed the ice maker lever to make sure it wouldn't try to produce ice while I was replacing it.

I removed the bottom screw and loosened the top two with a nut driver. The ice maker lifted right out and allowed me to disconnect the electrical plug; just sque eze the little plastic levers on both sides of the plug and pull.

I plugged in the electrical connection from the new ice maker. Making sure the water spout was in place, I dropped the new unit over the two loosened top screws. I then replaced the bottom screw and tightened all three. I replaced the ice catcher bucket and made myself a martini as a reward for not spending the $75.00 to $100.00 for a service call.

Within a couple of hours it was again making batches of ice for more martinis; it was a day or so before there was enough for frozen Margueritas.

I never even unplugged the refrigerator or shut off the water supply, although I suppose it would be prudent but not necessary. Some people like me just like to tempt fate.

The repair was so quick I didn't even worry about emptying the freezer. It was so easy even a girl could do it ... no offense intended. At the equivalent of $300.00 to $400.00 per hour I wish I could do it all day. Maybe I should be a "refrigerator repairman".

Seriously, the only thing that could hamper you is a lack of confidence which will quickly be overcome in 10 to 15 minutes by a huge ego. That time frame includes locating the tools and taking a few deep breaths. Don't hesitate to give it a shot. If you can't do it you really don't deserve to have ice. It really is that simple and easy.
Was this helpful?
Thank you for voting!
Ice maker sent water thru and frozen up ..no cubes
5 of 8 people found this instruction helpful.
  • H. from Maitland, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Followed the directions in the package. Turned off the power, removed two screws following the directions and replaced the entire unit. So easy even a Cave Man can do it. No kidding, and the best part was the fact that our local distributed wanted almost $20.00 more for the same part and I'd have to drive over a hour 40 miles to get it.
Was this helpful?
Thank you for voting!
leaking ice maker,big chunks ot ice were forming and had to remove them 2-3 times a day
4 of 5 people found this instruction helpful.
  • Linda from Johnson City, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self
Was this helpful?
Thank you for voting!
Ice maker just stopped making ice
4 of 5 people found this instruction helpful.
  • Thomas from Valencia, PA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver
This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same t ime to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.
Was this helpful?
Thank you for voting!
Ice maker stopped making ice
3 of 3 people found this instruction helpful.
  • Daniel from DAVISBURG, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.
Was this helpful?
Thank you for voting!
Fill cup broke.
6 of 12 people found this instruction helpful.
  • Aliki from Miami, FL
  • Really Easy
  • Less than 15 mins
Very easy to order from parts select. Took seconds to replace.
Was this helpful?
Thank you for voting!
Cam snapped in half on bottom of door
3 of 3 people found this instruction helpful.
  • Mason from Tallahassee, FL
  • Easy
  • Less than 15 mins
  • Screw drivers
Super easy - emptied door of all food, unscrewed bracket from top of door, lifted door off and set aside. Broken cam removed, new one screwed in, and lubed with some Vaseline. Set door back in new cam, screwed bracket into the top, and good to go. I was kinda worried about shopping from PartSelect since I had never heard about them, but t he part was here in less than 2 days. Pretty awesome little company.
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people found this instruction helpful.
  • Winston A from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
  • Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people found this instruction helpful.
  • Jane from Albuquerque, NM
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80.. .would have been at least $100 to have a repair person come to the house!
Was this helpful?
Thank you for voting!
door would not self close tightly
3 of 3 people found this instruction helpful.
  • paula from julian, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove two screws from top door hinge.
Remove door from unit
Remove old broken plastic cam 1 screw
Replace new door cam tighten 1 screw
Reinstall door and top hinge screws.
Was this helpful?
Thank you for voting!
clicking sound
3 of 3 people found this instruction helpful.
  • Ronald J from TULSA, OK
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged the power and removed the cardboard back Unplugged the part and power from the side of the compressor Plugged the power and new part back in to the side of the compressor and replaced the clamp Plugged in the power cord to the wall outlet and the refrigerator started to hum Job done Thanks
Was this helpful?
Thank you for voting!
Refrig began to trip the GFI circuit in the garage. When plugged into a house interior circuit the lights and fan ran but no cooling in either the freezer or frig.
3 of 3 people found this instruction helpful.
  • riley from CAVE CREEK, AZ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
First of all I want to thank Michael from Carlisle,PA and this site for publishing Michael's info on the wiring specifics on the new 3 connector Start Relay ( WP2262185 ). The original relay only has 2 connectors The 2 orange wires which are combined to one female connector need to be clipped and separated each to its own connector. Ref er to Michael's blog as to which wire goes to which connector on the Start Relay. I replaced the Run Capacitor, Start Relay and Overload just to be safe. The Start Relay was the actual culprit.Thank you for an excellent website!
Was this helpful?
Thank you for voting!
All Instructions for the 3653
106 - 120 of 778