36383 Kenmore - Instructions

Removed Ice Maker (2-Bolts)
Removed Ice Tray Screw Motor (to get to Ice Maker Plug- 4 small screws)
Installed new Ice Maker and reinstalled Ice Maker Screw Motor
Extreamly easy

Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!

TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.

Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)

Use adapter for t ... Read more he electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.

PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.

HAVE A COCKTAIL!

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on th ... Read more is refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.

Removed old Ice maker and replaced with new Ice maker.

pluged the wire harness into the new socket from the back and snaped the socket in place.

I ordered both a new replacement ice maker, and a new solenoid/pump. They were delivered to my house within one day and I had them installed in a matter of an hour. I had to use the power extension cord supplied with the ice maker.

The new "quick connect" hose couplings on the new pump are great.

A friend had no problem getting the new ice maker in. But then the problems started. The ice maker works great. But when the water fills the ice maker it squirts water onto the side of the freezer and ice sickles form. So we watched and decided the hole was too large so used a piece of plastic. That helped to cover the hole. But some wate ... Read more r is still entering the freezer and not all going to the ice maker. The only other thing we can think to try is to use epoxy to try to close that place. A simple job has turned into a big headache. I wish they made the ice maker like the original one.

Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 ... Read more min. Easy job! Great product! THANKS MJS

I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker co ... Read more ver. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.

Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done

My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.