363681 Kenmore Refrigerator - Instructions

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove fro ... Read more m hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

I removed the maker from the freezer, three phillps head screws, I pulled off the white plastic cover and found the top (small) gear had poped out, after carefull inspection, I notice two missing teeth. I ordered a new gear from ParstSelect re-installed and with in two days my ice maker was working like new. I estimate I saved myself seve ... Read more al hundred dollars, my wife wanted to call a service professional or worse buy a new refrigerator freezer. Thanks PartSelect!

Very easy. Removed all the parts from the fridge. Removed the glass. Unscrewed the two screws holding the rails to the front and rear support. The front support that has the "fruit" and veggie" settings, you have to remove the plastic name cover off to expose the front screws. The install is the reverse of the removal. The only "tricky" p ... Read more art is remembering the configuration (left from right) and removing the vinyl edging that the glass rests on from the old left and right rails and placing it on the new rails. Good Luck to all! "Quality is not an act, it is a habit" - Aristotle

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

I placed the new part on the end of the freezer door guard and firmly pushed it in until it 'clicked'. Easy as pie! The more difficult part was to remove the broken off part inside the opening of the freezer door hwere the new bar end was to be inserted. I finally used thin nose pliers to reach in and grab the broken off part.

I had to figure out how to remove the old gasket and install the new one on my own since there were NO INSTRUCTIONS. The old gasket had to be cut off; the new one had to be warmed in hot water to make it flexible enough to flatten out. Once that was done, I had to trim excess plastic from the inside corners before the gasket would press i ... Read more nto place at the corners.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

Wow, end result was amazing. I had to place my ear close to the refrigerator to find out if the fan was working. So quiet. Prior to this we could hear it in the bedroom. I replaced the fan motor, blade, grommets, i.e. the whole fan train. There were two screws holding the fan which were removed. (After removing the back panel.) Then ... Read more removed the old blade and dust cap. Detached the wiring harness at the junction. Then reassemble in the reverse order. I screwed up the 1st time...installed the front motor grommet in reverse. Fan blade was not centered. Resulted in a few mins rework. Actually spent more time cleaning all the dust from the compartment and behind the refer than it took to install the new fan system. Did I say that I couldn't be more pleased with the no noise result?

This was much easier than I anticipated.
The most time doing the repair was waiting for the water to soften the new seal.
The old one pulled right out, she cleaned it off and I pushed the other into place.
Part select got it to me quicker than expected and when I phoned the order in and inquired about whether I neede ... Read more d the retainer behind it she asked someone and found I did not which saved me $16.
They are great and this whole transaction went too smooth...

Found the part I needed in only a few minutes on the website and ordered it in less than 5 minutes. The part came within 2 days and I simply removed 2 screwes from the old part and installed the new part and replaced the 2 screws , the easiest repair job that I have ever done in my home. Thanks

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

I took out the vegetable bins and slid in the part. Replaced vegetable bins. Works perfect. I was told locally that GE doesn't make the part any more and that I wouldn't be able to find one. First place I looked on the net was you and found it with no trouble at all. really thrilled to get it. Thanks