36363 Kenmore Microwave - Instructions

Removed one phillips head screw, removed old cover, then replaced new cover and screw. Very easy and Parts Select made it happen. Will deal with them again. Thanks Parts Select.

removed screw that holds glass for light and replaced bulb.
Reinserted screw that holds glass.

Only down side was cost to ship small bulb.

Removed one Phillips screw, installed new wave guide cover, secured with phillips screw. Done

Another company said the new plate would arrive in mid-March, this company seemed to be faster so ordered the tray here, and it came in less than a week. I put the turn button back in the center hole, set the wheeled ring on the bottom of the oven, fitted the new glass tray onto the turn button.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other ... Read more and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

This is a simple task. Removed the choke cover using a putty knife or small flat screw driver. Putty knife works best. Slide putty knife under the plastic choke cover to lift up over clips all around the door. There are 3 on top and Bottom and 2 on each side. Be very careful or you will break the catch clips that hold the choke cover ... Read more in place. Lift the door latch up all the way and push towards the outside of the door, then pull the top or bottom out then the rest of it. Unhook the spring end from the door. Attach the new spring to the hook on the door and then to the door latch. Extend it up all the way so the 2 hook parts of the door latch can go back into their slots. Unlike some others said, the microwave door does not need to be removed. If you have someone to hold the door still, that's good enough. I did it by myself with no problem.

I read your instructions sent with the new latch. Looked at a couple videos online and it was VERY easy to change the part. Thanks so much?

Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of t ... Read more he freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door

Removed the light cover screw with a Phillips screwdriver. Removed the lamps from the packaging just enough to free up the 2 prongs for fitting in the socket. Make sure the power is in the "off position". Install the bulbs one at a time by lining up the 2 sockets (Very important not to touch the halogen bulb glass surface while installing ... Read more them). Energize the light switch to check operation of the new bulbs.

DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switc ... Read more hes (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK

Watched Utube instructions on how to do it to it and just did it.

Remove upper grill, then control panel, then 2 screws hold door switch mounting bracket, that will let you roll the switches out to work on them. Remove each switch by carefully pushing back retainer clips. Diode a long pair of needlenose pliers is helpful. The control board in front of capacitor comes out with a flat screwdriver and pry ... Read more up. Removing grnd wires helps

Using a phillips screwdriver I opened the panel in which the two lamps are located and easily removed the lamps. I ordered them through the internet and was pleasantly surprised when I received them the next day.

I removed the door, by taking off the grill at the top. Then, take the puddy knife and screw driver and pry the facing off of the door. Please remember to be very careful because this is a sensitive piece. This is the most difficult part. It is a piece of cake after this. This should take about 15 minutes from beginning to end.

We opened the microwave door and essentially with a straight screwdriver worked to "pop" the plastic frame off of the door. We tried to be less aggressive in our efforts and this paid off since we didn't break anything! The area we needed to work on was now exposed to put the new latch in. It took 2 hands rather than 3 to get the new latc ... Read more h attached and then wah-lah, It was done! Microwave works perfectly now. Great alternative to buying a new microwave!